Straw, Miscanthus, maize, and horse manure were reviewed in terms of fuel characteristics. They were tested in existing boilers, and the particulate and gaseous emissions were monitored. The ash was analyzed for the presence of sintered material. All the fuels showed problems with ash lumping and slag formation. Different boiler technologies showed different operational performances. Maize and horse manure are problematic fuels regarding NO_x and particulate emissions. Miscanthus was the best fuel tested. Due to the big variation of fuel properties and therefore combustion behavior of agricultural biomass, further R&D is required to adapt the existing boilers for these fuels.

Experimental data on the release of NO_x precursors from solid biomass fuels during thermal conversion are necessary to study N release in general and to supply reliable data for the purpose of packed bed and gas phase conversion model development and validation. In this work the release of NO_x precursors was studied at a lab-scale pot furnace (batch reactor) by taking measurements during the conversion process of solid biomass in a packed bed. The investigations were carried out with relevant woody biomass fuels, which cover a broad range of fuel N contents: sawdust, bark, waste wood and MDF board. The most important NO_x precursor detected above the fuel bed under fuel rich conditions was NH₃, while HCN was almost insignificant with the exception of sawdust. NO was detected mainly under air rich conditions. Furthermore, the experimental data were utilised to derive release functions for the relevant NO_x precursors NO, NH₃ and HCN. The release functions were implemented in an in-house empirical packed bed combustion model, which serves as a basis for a subsequent CFD N species gas phase calculation. © 2007 Elsevier Ltd. All rights reserved.

A one-dimensional model for the thermal conversion of thermally thick biomass particles is developed for the simulation of the fuel bed of biomass grate furnaces. The model can be applied for cylindrical and spherical particles. The particle is divided into four layers corresponding to the main stages of biomass thermal conversion. The energy and mass conservation equations are solved for each layer. The reactions are assigned to the boundaries. The model can predict the intra-particle temperature gradient, the particle mass loss rate as well as the time-dependent variations of particle size and density, as the most essential features of particle thermal conversion. When simulating the fuel bed of a biomass grate furnace, the particle model has to be numerically efficient. By reducing the number of variables and considering the lowest possible number of grid points inside the particle, a reasonable calculation time of less than 1 min for each particle is achieved. Comparisons between the results predicted by the model and by the measurements have been performed for different particle sizes, shapes and moisture contents during the pyrolysis and combustion in a single-particle reactor. The results of the model are in good agreement with experimental data which implies that the simplifications do not impair the model accuracy.

Der Einfluss von Nährstoffzusammensetzung und Additivzugabe beim anaeroben Abbau organischer Substanz stieß in den letzten Jahren vermehrt auf Interesse. Im Besonderen Spurenelemente haben erwiesenermaßen erheblichen Einfluss auf u.a. methanogene Archaeen und deren metabolische Aktivität. Massive Probleme der Prozessstabilität speziell bei Monovergärung unterschiedlichster Substrate können durch Co-Fermentation oder gezielte Zudosierung von Spurenelementmischungen überwunden werden. Ein profundes Verständnis der Wirkung dieser Elemente auf die verschiedenen mikrobiellen Spezies im Biogasreaktor als auch ihre Verfügbarkeit, ist die Voraussetzung für eine wirtschaftliche Gestaltung des anaeroben Fermentationsprozesses organischer Roh- als auch Reststoffe. Der heutige Stand-der-Technik zur Analyse von Biogasproben hat seinen Ursprung in der Wasser-, Abwasser- und Schlammanalytik und besteht aus einem einzelnen Filtrationsschritt vor Elementdetektion mittels ICP-OES bzw. ICP-MS. Diese Methodik erlaubt nur einen äußerst begrenzten Einblick in die Verteilung von essentiellen Spurenelementen in Anaerobreaktoren. Eine aussagekräftige Beurteilung der mikrobiellen Verfügbarkeit von beispielsweise Cobalt, Nickel oder Molybdän ist somit nur eingeschränkt möglich. Ziel dieser Arbeit war es, eine bestehende Methode zur sequentiellen Extraktion aus dem Bereich der Boden- und Sedimentanalytik für die Anwendung auf Biogasproben zu adaptieren. Der daraus resultierende Einblick in die Verteilung von Spurenelementen in den einzelnen Fraktionen erlaubt eine genauere Bewertung der mikrobiellen Verfügbarkeit von Nährstoffen in Biogasreaktoren, verglichen mit bestehenden analytischen Untersuchungsmethoden. Anforderungen an das Verfahren wie die Reproduzierbarkeit der Daten, zeitsparende Analytik und wirtschaftliche Realisierbarkeit konnten erfüllt werden. Wiederfindungsraten zwischen 90 und 110 % wurden für die wichtigsten Spurenelemente erreicht. Durch die sequentielle Extraktion konnte gezeigt werden, dass essenzielle Mikro-Nährstoffe bis zu 98 % in einer unlöslichen Form vorliegen können. Die Ergebnisse dieser Arbeit belegen die Anwendbarkeit der entwickelten Methodik zur Spurenelement-Extraktion in Anaerob-Systemen.

The aim of the current study was to investigate the feasibility of membrane contactors for continuous ammonia (NH₃-N) removal in an anaerobic digestion process and to counteract ammonia inhibition. Two laboratory anaerobic digesters were fed slaughterhouse wastes with ammonium (NH₄⁺) concentrations ranging from 6 to 7.4 g/L. One reactor was used as reference reactor without any ammonia removal. In the second reactor, a hollow fiber membrane contactor module was used for continuous ammonia removal. The hollow fiber membranes were directly submerged into the digestate of the anaerobic reactor. Sulfuric acid was circulated in the lumen as an adsorbent solution. Using this set up, the NH₄⁺-N concentration in the membrane reactor was significantly reduced. Moreover the extraction of ammonia lowered the pH by 0.2 units. In combination that led to a lowering of the free NH₃-N concentration by about 70%. Ammonia inhibition in the reference reactor was observed when the concentration exceeded 6 g/L NH₄⁺-N or 1-1.2 g/L NH₃-N. In contrast, in the membrane reactor the volatile fatty acid concentration, an indicator for process stability, was much lower and a higher gas yield and better degradation was observed. The chosen approach offers an appealing technology to remove ammonia directly from media having high concentrations of solids and it can help to improve process efficiency in anaerobic digestion of ammonia rich substrates. © 2012 Elsevier Ltd.

A one-dimensional single particle model is utilised to investigate the effects of radiation temperature, moisture content, particle size and biomass physical properties on the heating rate in biomass particles during pyrolysis. The model divides the particle into four layers - drying, pyrolysis, char and ash layer - corresponding to the four main stages of biomass thermal conversion. The average of the time derivative of the pyrolysis layer centre temperature weighted by the pyrolysis rate is introduced as an appropriate indicator for the heating rate in the particle during pyrolysis. The influencing parameters on the heating rate are summarised in the Biot number and the thermal time constant, to make the investigation of their effects easier. The heating rate is inversely proportional to the thermal time constant. The effect of a variation of the Biot number on the heating rate is negligible in comparison to the thermal time constant. Therefore, the thermal time constant can be sufficiently used to specify the heating rate regimes during pyrolysis. It is found that for thermal time constants of more than 50 s, pyrolysis takes place in a low heating rate regime, i.e. less than 50 K/min. Additionally, the heating rate during pyrolysis of various biomass types under a wide range of thermal conversion conditions has been examined, in order to classify the heating rate regime of pyrolysis in state-of-the-are combustion/gasification plants. The pyrolysis of wood dust and wood pellets is found to happen always in high heating rate regimes. Therefore, the kinetic parameters obtained by conventional TGA systems (typically with heating rates lower than 50 K/min) are not applicable for them. On the contrary, the pyrolysis of wood logs always happens in low heating rate regimes, which indicates that kinetic parameters obtained by conventional TGA systems can be applied. However, pyrolysis of wood chips can undergo low or high heating rate regimes depending on their particle size. Concerning the moisture content, it can be stated that it does not strongly influence the heating rate regime of certain biomass particles. © 2011 Elsevier Ltd. All rights reserved.

In this study, we investigated the emissions, including odor, from log wood stoves, burning wood types indigenous to mid-European countries such as Austria, Czech Republic, Hungary, Slovak Republic, Slovenia, Switzerland, as well as Baden-Württemberg and Bavaria (Germany) and South Tyrol (Italy). The investigations were performed with a modern, certified, 8 kW, manually fired log wood stove, and the results were compared to emissions from a modern 9 kW pellet stove. The examined wood types were deciduous species: black locust, black poplar, European hornbeam, European beech, pedunculate oak (also known as “common oak”), sessile oak, turkey oak and conifers: Austrian black pine, European larch, Norway spruce, Scots pine, silver fir, as well as hardwood briquettes. In addition, “garden biomass” such as pine cones, pine needles and dry leaves were burnt in the log wood stove. The pellet stove was fired with softwood pellets.

The composite average emission rates for log wood and briquettes were 2030 mg MJ⁻¹ for CO; 89 mg MJ⁻¹ for NO_x, 311 mg MJ⁻¹ for C_xH_y, 67 mg MJ⁻¹ for particulate matter PM₁₀ and average odor concentration was at 2430 OU m⁻³. CO, C_xH_y and PM₁₀ emissions from pellets combustion were lower by factors of 10, 13 and 3, while considering NO_x – comparable to the log wood emissions. Odor from pellets combustion was not detectable. CxHy and PM10 emissions from garden biomass (needles and leaves) burning were 10 times higher than for log wood, while CO and NO_x rise only slightly. Odor levels ranged from not detectable (pellets) to around 19,000 OU m⁻³ (dry leaves). The odor concentration correlated with CO, C_xH_y and PM₁₀. For log wood combustion average odor ranged from 536 OU m⁻³ for hornbeam to 5217 OU m⁻³ for fir, indicating a considerable influence of the wood type on odor concentration.

urpose: Decreasing energy demand due to improved building standards requires the development of new biomass combustion technologies to be able to provide individual biomass heating solutions. The purpose of this paper is, therefore, the development of a pellet water heating stove with minimal emission at high thermal efficiency. Design/methodology/approach: The single components of a 10 kW water heating pellet stove are analysed and partly redesigned considering the latest scientific findings and experimental know-how in combustion engineering. The outcome of this development is a 12 kW prototype which is subsequently down-scaled to a 6 kW prototype. Finally, the results of the development are evaluated by testing of an accredited institute. Findings: Based on an existing pellet water heating stove, the total excess air ratio was reduced, a strict air staging was implemented and the fuel supply was homogenized. All three measures improved the operating performance regarding emissions and thermal efficiency. The evaluation of the development process showed that the CO emissions are reduced by over 90 per cent during full load and by 30-60 per cent during minimum load conditions. Emissions of particulate matter are reduced by 70 per cent and the thermal efficiency increased to 95 per cent. Originality/value: The result represents a new state of technology in this sector for minimal emissions and maximal thermal efficiency, which surpasses the directives of the Eco label "UZ37" in Austria and "Blauer Engel" in Germany, which are amongst the most stringent performance requirements in the European Union. Hence this design possesses a high potential as heating solution for low and passive energy houses. © Emerald Group Publishing Limited.

Biogas substrates are typically moist, which can make them difficult to store because bacteria and mould can grow on them. Ensiling, which involves the production of acid by lactic acid bacteria, is often used to preserve crops cheaply. Biogas substrates are also often fibrous, which can make them difficult to mix and means that some of their energy is locked up within the fibres. Different pre-treatment technologies are being investigated to access the energy in these fibres, to increase the rate of biogas production and to improve the mixing qualities of the substrates. Pre-treatment technologies are based on three principles: physical (including mechanical shear, heat, pressure and electric fields), chemical (acids, bases and solvents) and biological (microbial and enzymatic). Combinations of these principles are also used, including steam explosion, extrusion and thermo-chemical processes. Although many of these processes have been investigated at small scale, few have been analysed at large scale in un-biased studies. Many of these techniques are associated with high energy input (e.g. mechanical and heat pre-treatment), high equipment costs (e.g. mechanical systems where the blades erode) or use large volumes of chemicals (e.g. alkali pre-treatment). Different pre-treatment technologies work better with different substrates, and more research is required in this field to understand which combinations are worthwhile. This chapter describes some of the common pre-treatment technologies along with some advantages and disadvantages.

Synthesis gas from biomass can be produced and utilized in different ways. Conversion of biomass to synthesis gas can be done either in fluidized bed or entrained flow reactors. As gasification agent oxygen, steam, or mixtures are used. The most common use of biomass gasification in the last decades has been for heat and/or power production. Nowadays, the importance of transportation fuels from renewables is increased due to environmental aspects and growing fossil fuels prices. That is why the production of Fischer-Tropsch (FT) liquids, methanol, mixed alcohols, substitute natural gas (SNG), and hydrogen from biomass is now in focus of view. The most innovative and interesting ways of synthesis gas utilization and projects, BioTfueL or GoBiGas, BioLiq, Choren, etc. are discussed here. Further the microchannel technology by Oxford Catalysts and distributed production of SNG in decentral small scale are presented. The synthesis platform in Güssing, Austria is also presented. The FT liquids, hydrogen production, mixed alcohols, and BioSNG, these are the projects associated with the FICFB gasification plant in Güssing. Also the principle and examples of sorption-enhanced reforming to adjust H₂/CO ratio in product gas during the gasification is described. Finally, in the conclusion also an outlook for the thermochemical pathway to transportation fuels is given. WIREs Energy Environ 2014, 3:343-362. doi: 10.1002/wene.97 For further resources related to this article, please visit the WIREs website. © 2013 Wiley Periodicals, Inc.

Trace nutrients significantly affect the microbial metabolic activity within anaerobic digestion processes but always imply the risk of overdosing of heavy metals. In this study the applicability of a sequential extraction scheme established for soil and sediment samples on biogas slurries with different compositions was tested and compared to an adapted version of this extraction method. The analytical results proved the successful applicability of the developed analytical technique for the speciation of trace nutrients in anaerobic digestion systems. The procedure fulfills the basic requirements of reproducible data, a time-saving analytical approach and economic feasibility. Recovery rates of 90-110% were obtained for the most important trace elements Fe, Co, Cu, Mo, Ni and Zn. However, it was demonstrated that the adapted method provides more reliable information about the bioavailable fractions and it is considered the more appropriate approach. Data on fractionation indicated that up to 76% of these essential trace nutrients might be present in an insoluble state. Depending on the specific trace element a significant fraction, from 30% to more than 70%, is not directly bioavailable. This important aspect should be considered to guarantee sufficient supply of the microbial consortium with trace elements and at the same time to avoid overdosage. © 2014 Elsevier Ltd.

Three mono-digestion experiments treating slaughterhouse waste with high TKN concentration (~11. g/kg) were applied in lab-scale at mesophilic and psychrophilic conditions to study the impact of high ammonia concentrations and additives. Precipitation of sulphur by addition of ferrous chloride did not influence process behaviour, whereas supplementation of trace elements significantly improved process stability by reducing volatile fatty acid concentration towards zero.The limit of NH₄-N concentration causing a rise of VFAs to 19,000mg/l and reduction of methane by 25% was found between 7.7 and 9.1g/kg which correspond to NH₃ concentrations of 830-1060mg/l.Psychrophilic operation (25°C) lowered inhibitory NH₃ concentration to 140mg/l, but process performance was stable only at low OLR of 0.4kgVS/m³d.Robust performance at highest possible NH₄-N concentration (7.7g/kg), low VFA accumulation and satisfying methane yield of about 280Nm3/t COD was observed at OLR of 2.5kgVS/m³d at 37°C. © 2014 Elsevier Ltd.

Because of increased efforts to reduce CO₂ emissions a significant step in the development of small-scale (residential) biomass boilers for space heating has been achieved in recent years. Currently, the full potential for low-emission operation at high efficiencies, which is in principle possible due to optimized furnace geometries as well as combustion air staging strategies, cannot be exploited since there is still the need to enhance the controllers applied. For this reason, a model based control strategy for small-scale biomass boilers was developed and successfully implemented in a commercially available system. Thereby, appropriate mathematical models were developed for all relevant parts of the furnace and connected to an overall model subsequently used for the control unit design. The resulting controller is based on the input–output linearization and the state variables are estimated by an extended Kalman filter. Finally, the new control was implemented at a commercially available small-scale biomass boiler and the experimental verification showed a significant improvement of the operating behaviour in comparison to the conventional control.

A transient 3D model for two main zones, namely the fuel bed and the freeboard, of biomass packed bed combustion systems was developed. It integrates the models for the biomass conversion sub-processes and solves the governing equations for the gas and solid phase and their interactions. The intra-particle gradients are included by considering the biomass particles as thermally thick particles. The shrinkage of the packed bed and the variations of the bed porosity due to the uneven consumption of the fuel are taken into account. Detailed kinetic mechanisms are used for the simulation of homogeneous gas phase reactions. To verify the model and to increase the understanding of packed bed combustion, laboratory-scale fixed-bed batch experiments have been performed in a reactor with 9.5 cm diameter and 10 cm length. The model performance was extensively validated with gas phase measurements (CO, CO₂, CH₄, H₂, H₂O and O₂) above the fuel bed, temperatures at different heights in the bed and in the freeboard, and the propagation rate of reaction front. The simulation results are in a good agreement with the measured values. © 2014 Elsevier Ltd. All rights reserved.

Anaerobic digestion (AD) of sugar beet pressed pulp (SBPP) is a promising treatment concept. It produces biogas as a renewable energy source making sugar production more energy efficient and it turns SBPP from a residue into a valuable resource. In this study one- and two-stage mono fermentation at mesophilic conditions in a continuous stirred tank reactor were compared. Also the optimal incubation temperature for the pre-acidification stage was studied. The fastest pre-acidification, with a hydraulic retention time (HRT) of 4 days, occurred at a temperature of 55 °C. In the methanogenic reactor of the two-stage system stable fermentation at loading rate of 7 kg VS/m³ d was demonstrated. No artificial pH adjustment was necessary to maintain optimum levels in both the pre-acidification and the methanogenic reactor. The total HRT of the two-stage AD was 36 days which is considerably lower compared to the one-stage AD (50 days). The frequently observed problem of foaming at high loading rates was less severe in the two-stage reactor. Moreover the viscosity of digestate in the methanogenic stage of the two-stage fermentation was in average tenfold lower than in the one-stage fermentation. This decreases the energy input for the reactor stirring about 80 %. The observed advantages make the two-stage process economically attractive, despite higher investments for a two reactor system. © 2013 Springer Science+Business Media Dordrecht.
 

An active condensation system for the heat recovery of biomass boilers is evaluated. The active condensation system utilizes the flue gas enthalpy exiting the boiler by combining a quench and a compression heat pump. The system is modelled by mass and energy balances. This study evaluates the operating costs, primary energy efficiency and greenhouse gas emissions on an Austrian data basis for four test cases. Two pellet boilers (10kW and 100kW) and two wood chip boilers (100kW and 10MW) are considered. The economic analysis shows a decrease in operating costs between 2% and 13%. Meanwhile the primary energy efficiency is increased by 3-21%. The greenhouse gas emissions in CO2 equivalents are calculated to 15.3-27.9kg MWh-1 based on an Austrian electricity mix. The payback time is evaluated on a net present value (NPV) method, showing a payback time of 2-12 years for the 10MW wood chip test case. © 2014 Elsevier Ltd.

The results of experimental work to investigate the effects of air staging on emissions from energy crop combustion in small scale applications are presented. Five different biomass fuels (wood, willow, miscanthus, tall fescue and cocksfoot) were combusted in a small scale (35 kW) biomass boiler and three different tests looking at the effects of (1) air ratio in the primary combustion chamber (primary air ratio), (2) temperature in the primary combustion chamber, and (3) overall excess air ratio, on NO_x and particulate emissions were conducted. It was shown that by varying the primary air ratio, NO_x emission reductions of between 15% (wood) and 30% (Miscanthus) and PM₁ reductions of between 16% (cocksfoot) and 26% (wood) were possible. For all fuels, both NO_x and particulate emissions were minimised at a primary air ratio of 0.8. Particulate emissions from miscanthus increased with increasing temperature in the primary combustion chamber, NO_x emissions from Miscanthus and from willow also increased with temperature. Overall excess air ratio has no effect on emissions as no significant differences were found for any of the fuels. Emissions of particulates and oxides of nitrogen from a wide range of biomass feedstocks can be minimised by optimising the primary air ratio and by maintaining a temperature in the primary combustion chamber of approximately 900 °C.

Anaerobic digestion offers a good opportunity to degrade residues from breweries to biogas. To improve the anaerobic degradation process thermal pretreatment of brewers' spent grains (BSG) offers the opportunity to increase degradation rate and biogas yield. Aim of the work is to show the influence of the thermal pretreatment of BSG to anaerobic digestion. BSG were pretreated at different temperature levels from 100 to 200°C. The biogas production of thermally pretreated BSG lies between 30 and 40% higher than for untreated reference. The temperature of the pretreatment process has a significant influence on the degradation rate or gas yield, respectively. Up to a temperature of 160°C, the biogas yield rises. Temperatures over 160°C result in a slower degradation and decreasing biogas yield. Substrate with and without pretreatment gave a daily biogas yield of 430 and 389 Nm³ × kg^-1 VS, respectively. Batch analysis of the biochemical methane potential gives a total methane yield of 409.8 Nm3 CH₄ × kg^-1 VS of untreated brewers' spent grains and 467.6 Nm3 CH₄ × kg^-1 VS of the pretreated samples. For pretreatment energy balance estimation has been carried out. Without any heat recovery demand is higher than the energy surplus resulting from pretreatment of BSG. With energy recovery by heat exchanger the net energy yield could be increased to 38.87 kWh × kg^-1 FM or 8.81%. © 2015 American Institute of Chemical Engineers Environ Prog.

To gain reliable data for the development of an empirical model for the prediction of the local high temperature corrosion potential in biomass fired boilers, online corrosion probe measurements have been carried out. The measurements have been performed in a specially designed fixed bed/drop tube reactor in order to simulate a superheater boiler tube under well-controlled conditions. The investigated boiler steel 13CrMo4-5 is commonly used as steel for superheater tube bundles in biomass fired boilers. Within the test runs the flue gas temperature at the corrosion probe has been varied between 625 °C and 880 °C, while the steel temperature has been varied between 450 °C and 550 °C to simulate typical current and future live steam temperatures of biomass fired steam boilers. To investigate the dependence on the flue gas velocity, variations from 2 m·s⁻¹ to 8 m·s⁻¹ have been considered. The empirical model developed fits the measured data sufficiently well. Therefore, the model has been applied within a Computational Fluid Dynamics (CFD) simulation of flue gas flow and heat transfer to estimate the local corrosion potential of a wood chips fired 38 MW steam boiler. Additionally to the actual state analysis two further simulations have been carried out to investigate the influence of enhanced steam temperatures and a change of the flow direction of the final superheater tube bundle from parallel to counter-flow on the local corrosion potential.

The direct combustion of the biomass is the most advanced and mature technology in the field of energetic biomass utilisation. The legislations on the amount of emitted pollutants and the plant efficiency of biomass combustion systems are continually being restricted. Therefore constant improvement of the plant efficiency and emission reduction is required Numerical modelling is gaining increasing importance for the development of biomass combustion technologies. In this paper an overview about the numerical modelling efforts deal with the most relevant phenomena in biomass grate firing systems is given. The numerical modelling results in a deeper understanding of the underlying processes in biomass combustion plants. Therefore, it leads to a faster and safer procedure of development of a new technology.

Industrial waste streams from brewing industries and distilleries provide a valuable but largely unused alternative substrate for biogas production by anaerobic digestion. High sulfur loads in the feed caused by acidic pretreatment to enhance bioavailability are responsible for H₂S formation during anaerobic digestion. Microbiological oxidation of H₂S provides an elegant technique to remove this toxic gas compound. Moreover, it allows for recovery of sulfuric acid, the final product of aerobic sulfide oxidation, as demonstrated in this study. Two-stage anaerobic digestion of brewer’s spent grains, the major byproduct in the brewing industry, allows for the release of up to 78% of total H₂S formed in the first pre-acidification stage. Desulfurization of such pre-acidification gas in continuous acidic biofiltration with immobilized sulfur-oxidizing bacteria resulted in a maximum H₂S elimination capacity of 473 g m^–3 h^–1 at an empty bed retention time of 91 s. Complete H₂S removal was achieved at inlet concentrations of up to 6363 ppm. The process was shown to be very robust, and even after an interruption of H₂S feeding for 10 days, excellent removal efficiency was immediately restored. A maximum sulfate production rate of 0.14 g L^–1 h^–1 was achieved, and a peak concentration of 4.18 g/L sulfuric acid was reached. Further experiments addressed the reduction of fresh water and chemicals to minimize process expenses. It was proven that up to 50% of mineral medium that is required in large amounts during microbiological desulfurization can be replaced by the liquid fraction of the digestate. The conducted study demonstrates the viability of microbial sulfur recovery with theoretical recovery rates of up to 44%.

A promising way to substitute fossil fuels for production of electricity, heat, fuels for transportation and synthetic chemicals is biomass steam gasification in a dual fluidized bed (DFB). Using lower-cost feedstock, such as logging residues, instead of stemwood, improves the economic operation. In Senden, near Ulm in Germany, the first plant using logging residues is successfully operated by Stadtwerke Ulm. The major difficulties are slagging and deposit build-up. This paper characterizes inorganic components of ash forming matter and draws conclusions regarding mechanisms of deposit build-up. Olivine is used as bed material. Impurities, e.g., quartz, brought into the fluidized bed with the feedstock play a critical role. Interaction with biomass ash leads to formation of potassium silicates, decreasing the melting temperature. Recirculation of coarse ash back into combustion leads to enrichment of critical fragments. Improving the management of inorganic streams and controlling temperature levels is essential for operation with logging residues.

State-of-the-art packed bed models supply continuous concentration profiles as boundary conditions for subsequent CFD simulations of gas phase, leading to pre-mixed combustion conditions. However, in reality the “porous” nature of the packed bed leads to streak formation influencing gas mixing and combustion. Therefore, in the present work, in order to account for the influence of the streaks on gas phase combustion, a gas streak model based on a correlation between the local gas residence time and a mixing time has been developed based on numerical simulations. Finally, the streak model was linked with an in-housed developed hybrid gas phase combustion model suitable for laminar to highly turbulent flow conditions and applied for an under-feed pellet stoker furnace (20 kW_th) concerning the simulation of gas phase combustion and NO_x formation. The results in comparison with a simulation without the streak formation model show that the flue gas species prediction can be improved with the proposed streak formation model. Especially, in the region above the fuel bed (in the primary combustion chamber), this is of special importance for NO_x reduction by primary measures.

Abattoirs have a large number of energy intensive processes. Beside energy supply, disposal costs of animal by-products (ABP) are the main relevant cost drivers. In this study, successful implementation of a new waste and energy management system based on anaerobic digestion is described. Several limitations and technical challenges regarding the anaerobic digestion of the protein rich waste material had to be overcome. The most significant problems were process imbalances such as foaming and floatation as well as high accumulation of volatile fatty acids and low biogas yields caused by lack of essential microelements, high ammonia concentrations and fluctuation in operation temperature. Ultimately, 85% of the waste accumulated during the slaughter process is converted into 2700 MW h thermal and 3200 MW h electrical energy in a biogas combined heat and power (CHP) plant. The thermal energy is optimally integrated into the production process by means of a stratified heat buffer. The energy generated by the biogas CHP-plant can cover a significant share of the energy requirement of the abattoir corresponding to 50% of heat and 60% of electric demand, respectively. In terms of annual cost for energy supply and waste disposal a reduction of 63% from 1.4 Mio € to about 0.5 Mio € could be achieved with the new system. The payback period of the whole investment is approximately 9 years. Beside the economic benefits also the positive environmental impact should be highlighted: a 79% reduction of greenhouse gas emissions from 4.5 Mio kg CO₂ to 0.9 Mio kg CO₂ annually was achieved. The realized concept received the Austrian Energy Globe Award and represents the first anaerobic mono-digestion process of slaughterhouse waste worldwide.

Nowadays dynamic building simulation is an essential tool for the design of heating systems for residential buildings. The simulation of buildings heated by biomass systems, first of all needs detailed boiler models, capable of simulating the boiler both as a stand-alone appliance and as a system component. This paper presents the calibration and validation of a boiler model by means of laboratory tests. The chosen model, i.e. TRNSYS "Type 869", has been validated for two commercially available pellet boilers of 6 and 12. kW nominal capacities. Two test methods have been applied: the first is a steady state test at nominal load and the second is a load cycle test including stationary operation at different loads as well as transient operation. The load cycle test is representative of the boiler operation in the field and characterises the boiler's stationary and dynamic behaviour. The model had been calibrated based on laboratory data registered during stationary operation at different loads and afterwards it was validated by simulating both the stationary and the dynamic tests. Selected parameters for the validation were the heat transfer rates to water and the water temperature profiles inside the boiler and at the boiler outlet. Modelling results showed better agreement with experimental data during stationary operation rather than during dynamic operation. Heat transfer rates to water were predicted with a maximum deviation of 10% during the stationary operation, and a maximum deviation of 30% during the dynamic load cycle. However, for both operational regimes the fuel consumption was predicted within a 10% deviation from the experimental values. © 2014 Elsevier Ltd.

This study investigates the general concept of reduced firebed temperatures in residential wood pellet boilers. Residential wood pellet boiler development is more and more concerned with inorganic aerosols characterized by a temperature-dependent release from the firebed. Hence, different concepts are applied aiming to reduce firebed temperatures. Unfortunately, these concepts influence not only firebed temperatures, but also other important parameters like air flow rates which may cause unwanted side effects with respect to combustion quality or efficiency. Thus, a new approach was developed solely affecting firebed temperature by implementing a water-based firebed cooling in a 12 kW underfeed pellet boiler. The effectiveness of the cooling was monitored by comprehensive temperature measurement in the firebed. The cooling capacity ranged from 0.4 kW to 0.5 kW resulted in a significant decrease of firebed temperatures. Gaseous emissions remain stable showing no significant changes in major components (O₂, CO₂, NO_x). Furthermore, CO emissions were even reduced significantly by the activated cooling, which was supposedly caused by a stabilized devolatilization due to the firebed cooling. Moreover, the temperature-dependent release of aerosol forming elements was influenced at activated firebed cooling, which is proved by a decrease of 17 wt% of dust (Total Suspended Particles; TSP). At the same time the gaseous emissions of HCl increase, supposedly by a reduced potassium release from the firebed to the gas phase and a subsequently different particle formation. The general concept of reduced firebed temperatures proved to be successful decreasing overall aerosol emissions without impacting combustion quality.

High-temperature corrosion in biomass fired boilers is still an insufficiently explored phenomenon which causes unscheduled plant shutdowns and hence, economical problems. To investigate the high-temperature corrosion and deposit formation behaviour of superheater tube bundles, online corrosion probe as well as deposit probe measurements have been carried out in a specially designed fixed bed/drop tube reactor in order to simulate a superheater boiler tube under well-controlled conditions. The investigated boiler steel 13CrMo4-5 is commonly used as steel for superheater tube bundles in biomass fired boilers. Forest wood chips and quality sorted waste wood (A1-A2 according to German standards) as relevant fuels have been selected to investigate the influence on the deposit formation and corrosion behaviour. The following influencing parameter variations have been performed during the test campaigns: flue gas temperature between 650 and 880°C, steel temperature between 450 and 550°C and flue gas velocity between 2 and 8 m/s. One focus of the work presented is the detailed investigation of the structure and the chemical composition of the deposits formed as well as of the corrosion products. A further goal of the work presented was the development of an empirical model which can be used within CFD simulations of flow and heat transfer to calculate and evaluate the local corrosion potential of biomass fired plants already at the planning stage. The corrosion probe measurements show a clear dependency on the parameters investigated and the empirical function developed reproduces the measured corrosion behaviour sufficiently accurate. Since the additional calculation time within the CFD simulation is negligible the model represents a helpful tool for plant designers to estimate whether high-temperature corrosion is of relevance for a certain plant or not, when using fuels with similar compositions and the steel 13CrMo4-5. © 2014 Elsevier Ltd. All rights reserved.

An efficient utilization of biomass fuels in power plants is often limited by the melting behavior of the biomass ash, which causes unplanned shutdowns of the plants. If the melting temperature of the ash is locally exceeded, deposits can form on the walls of the combustion chamber. In this paper, a bubbling fluidized bed combustion chamber with 50 MW biomass input is investigated that severely suffers deposit build-up in the freeboard during operation. The deposit layers affect the operation negatively in two ways: they act as an additional heat resistance in regions of heat extraction, and they can come off the wall and fall into the bed and negatively influence the fluidization behavior. To detect zones where ash melting can occur, the temperature distribution in the combustion chamber is calculated numerically using the commercial CPFD (computational particle fluid dynamics) code, Barracuda Version 15. Regions where the ash melting temperature is exceeded are compared with the fouling observed on the walls in the freeboard. The numerically predicted regions agree well with the observed location of the deposits on the walls. Next, the model is used to find an optimized operating point with fewer regions in which the ash melting temperature is exceeded. Therefore, three cases with different distributions of the inlet gas streams are simulated. The simulations show if the air inlet streams are moved from the freeboard to the necking area above the bed a more even temperature distribution is obtained over the combustion chamber. Hence, the areas where the ash melting temperatures are exceeded are reduced significantly and the formation of deposits in the optimized operational mode is much less likely.

In this paper, the performance of a commercial Fe/Cr based catalyst for the water gas shift reaction was investigated. The catalyst was used in a water gas shift pilot plant which processed real product gas from a commercial biomass steam gasification plant with two different qualities: extracted before and extracted after scrubbing with a rapeseed methyl ester gas scrubber. The performance of the WGS pilot plant regarding these two different gas qualities was investigated. For this reason, extensive chemical analyses were carried out. CO, CO₂, CH₄, N₂, O₂, C₂H₆, C₂H₄, and C₂H₂ and H₂S, COS, and C₄H₄ S were measured. In addition, GCMS tar and NH₃ analyses were performed. Furthermore, the catalyst's activity was observed by measuring the temperature profiles along the reactors of the water gas shift pilot plant. During the 200 h of operation with both product gas qualities, no catalyst deactivation could be observed. A CO conversion up to 93% as well as a GCMS tar reduction (about 28%) along the water gas shift pilot plant was obtained. Furthermore, a specific H₂ production of 63 g H₂ per kg biomass (dry and ash free) was reached with both product gas qualities. No significant performance difference could be observed.

The interest in experimental data regarding thermal fuel decomposition as well as the release behavior of ash-forming elements of biomass fuels for modeling and simulation purposes is continuously increasing. On the basis of combustion experiments with lab-scale reactors and single-particle reactors, integral release data regarding ash-forming vapors can be obtained, whereby the release is calculated on the basis of analysis data of the fuel and the ash residues. At the moment, almost no time-resolved release data of ash-forming elements from single particles exist. Therefore, a single-particle reactor was designed, which has been coupled to an inductively coupled plasma mass spectrometer (ICP-MS). This reactor can be used for targeted experiments in a temperature range of 250–1050 °C under inert, reducing, and oxidizing conditions. With this reactor, it is possible to simultaneously determine the surface and center temperatures of a biomass particle, weight loss of the particle, and flue gas composition. The reactor has been coupled to an ICP-MS through a gas stream that is sufficiently diluted with Ar. First performance tests with pure salts (KCl, NaCl, (NH₄)₂SO₄, ZnCl₂, and PbCl₂) proved that relevant volatile ash-forming elements can be detected with the ICP-MS. For a further validation of the received signals, combustion tests with Miscanthus pellets have been carried out, whereby the controlled interruption of the experiments has also been investigated. These tests prove that with this system the simultaneous time-resolved determination of S, Cl, K, Na, Zn, and Pb is possible whereby the Cl signal can only be used with restrictions. On the basis of the determined release of ash-forming elements for the entire combustion experiment, a quantification/calibration of the measured intensities has been carried out. The data gained from these tests will provide deeper insights into release processes as well as form a relevant basis for release model development.

In modern buildings with tight shells, often room-independent air supply is required for proper operation of biomass stoves. One possibility to arrange this supply is to use a double-wall chimney with flue gas leaving through the pipe and fresh air entering through the annular gap. A one-dimensional quasi-static model based on balance equations has been developed and compared with experimental data. Inclusion of leak air is crucial for reproduction of the experimental results. © 2014, Springer-Verlag Berlin Heidelberg.

Biochar is the product of biomass pyrolysis and gasification. One of the possible application of this product is certainly in agronomic sector, as soil amendment. However biochar use in Italy is subordinated to insert this product in fertilizer list, which biochar could be commercialized with. The aim of this paper is to know the biochar from gasification process (using an Imbert downdraft prototype), in particular investigating its potentiality as soil amendment in terms of European and Italian regulations and in terms of physical and chemical characterizations.

Wood pellets have been reported to emit toxic gaseous emissions during transport and storage. Carbon monoxide (CO) emission, due to the high toxicity of the gas and the possibility of it being present at high levels, is the most imminent threat to be considered before entering a pellet storage facility. For small-scale (<30 tons storage capacity) residential pellet storage facilities, ventilation, preferably natural ventilation utilizing already existing openings, has become the most favored solution to overcome the problem of high CO concentrations. However, there is little knowledge on the ventilation rates that can be reached and thus on the effectiveness of such measures. The aim of the study was to investigate ventilation rates for a specific small-scale pellet storage system depending on characteristic temperature differences. Furthermore, the influence of the implementation of a chimney and the influence of cross-ventilation on the ventilation rates were investigated. The air exchange rates observed in the experiments ranged between close to zero and up to 8 m³h^-1, depending largely on the existing temperature differences and the existence of cross-ventilation. The results demonstrate that implementing natural ventilation is a possible measure to enhance safety from CO emissions, but not one without limitations. © 2014 © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Adsorptive on-board desulfurization units require a high desulfurization and regeneration performance for a wide range of fuels to keep them small and ensure long maintenance intervals. A novel thermal regeneration strategy was investigated in this work, fulfilling all requirements for in situ on-board regeneration. In this strategy, a temperature-controlled flow rate (TCFR) of air was used to control the temperature inside the adsorber. With this dynamic approach, the regeneration time was reduced significantly in comparison to other thermal regeneration strategies. The novel regeneration strategy was tested using Ag–Al₂O₃ as an adsorbent to desulfurize a benzothiophen (BT)-enriched road diesel (300 ppmw of total sulfur). A commercial diesel containing fatty acid methyl ester (FAME) was used to evaluate the fuel flexibility regarding desulfurization and regeneration performance. In the case of 6.63 wt % FAME and 300 ppmw of sulfur, the breakthrough adsorption capacity of sulfur decreased from 1.04 to 0.17 mg/g. In TCFR regeneration experiments, the breakthrough adsorption capacity was restored to over 94% in the case of both fuels. Thereby, the Brunauer–Emmett–Teller (BET) surface area of the regenerated adsorbent decreased by only 1.5%, and negligible carbon deposits were detected.

Nowadays prefabricated houses are becoming increasingly popular, thanks to their low cost and high energy performance. Heating systems installed in these houses should be carefully designed and controlled, to ensure sufficient thermal comfort while maintaining low fuel consumptions. This study presents the simulation of different system configurations and control strategies for a pre-fabricated house, located in Lower Austria. The house is heated by a 6 kW pellet boiler directly connected to a floor heating system, in a configuration without buffer storage tank. Using the TRNSYS simulation suite, a coupled simulation of the house and its heating and hot water supply system was set up, calibrated and validated with reference to monitoring data. As monitoring data evidenced that the control strategy of the heating system is not ideal to maintain a comfortable indoor temperature during the whole day, two improved strategies were simulated over the heating season and evaluated in terms of thermal comfort, pellet consumption and boiler’s efficiency. Moreover, to better understand the influence of the system configuration, simulations have been repeated considering another heat distribution system (radiators instead of floor heating). Results show that the radiators’ network, if adequately controlled, reduces by 85% the total discomfort time. In addition, the pellet boiler mainly operates in load modulation regime, leading to lower pellet supply rates and therefore to lower pellet consumptions (18% less than floor heating). However, the lower operational loads and frequent ignitions result in a slightly lower efficiency of the pellet boiler (4% less than the configuration with floor heating.

Biochars produced from pelletized grape vine (GV) and sunflower husk (SFH) agricultural residues were studied by pyrolysis in a batch reactor at 400 and 500 °C. Chemical and physical evolution of the biomass under pyrolysis conditions was determined and the products were characterized, including the main gaseous organic components. Results showed a decrease in solid biochar yield with increasing temperature. Biochar is defined as a “porous carbonaceous solid” produced by thermochemical conversion of organic materials in an oxygen depleted atmosphere, which has physiochemical properties suitable for the safe and long-term storage of carbon in the environment and, potentially, soil improvement. The aim of this work is to improve the knowledge and acceptability of alternative use of the biochar gained from agro-forestry biomass residuals, such as grape vine and sunflower husks, by means of modern chemical and physical characterization tools.

The dual fluidized bed (DFB) steam gasification technology of biomass was developed at Vienna University of Technology and is well-established for transforming biomass into a product gas which can be used for further applications. The DFB steam gasification reactor consists of a gasification chamber (bubbling bed, fluidized with steam) and a combustion chamber (turbulent bed, fluidized with air). Biomass is fed into the gasification chamber and gets in contact with the bed material, typically Olivine, at about 840°C. The released volatiles leave the gasification reactor as product gas. A part of the solid residue, called char, flows with the bed material via a chute to the combustion chamber where it is burnt with air. The bed material is heated up, separated from the flue gas stream in a cyclone and flows back to the gasification reactor via a loop seal where it provides the heat for devolatilization and drying of the biomass. The movement of the char is crucial since a sufficient amount has to flow to the combustion chamber and burn to provide enough energy for bed material heat-up. Up to now little is known about the char concentration in the bed material recirculation stream (or short recirculation stream) and its influencing variables. Therefore, a cold flow model, operated with ambient air, was constructed to study the influence of various parameters on the char concentration in the recirculation stream. Bronze is used as bed material since is matches closest to the scaling criteria. The char is also scaled; polyethylene is used as model char.

The cold flow model, see Figure 1 for the flowsheet, consists of a “gasification chamber” which corresponds to the gasification chamber in the hot plant and is as well operated as a bubbling bed. Via a chute the recirculation stream moves to a rotary valve which enables to set a fixed recirculation rate and make it independent from the following pneumatic conveying. Then, gas and solids are separated in a cyclone and the recirculation stream finally flows back to the gasification chamber. After the loop seal samples are taken for investigation of the model char concentration in the recirculation stream. In the present study the influence of fluidization rate in the gasification chamber, bed material recirculation rate and model char mass in the system on the char concentration in the recirculation stream are investigated. It was found that the model char particles show a flotsam behavior. Higher fluidization rates increase the model char concentration in the recirculation stream because of better mixing, whereas the bed material recirculation rate has only little influence. Doubling and tripling the overall char mass in the system did not lead to a doubling or tripling model char concentration in the recirculation stream. The present observations are helping to better understand the ongoing phenomena inside of the dual fluidized bed gasification reactor and provide knowledge to further optimize it.

Ash related problems such as slagging, fouling, and high temperature corrosion in biomass fired boilers are still insufficiently explored due to the complexity of the underlying processes. High temperature corrosion of low alloy steels like 13CrMo4-5 has already been investigated in plants firing chemically untreated wood chips. In this earlier work it has been suggested that the oxidation of the steel is the dominating mechanism in the material temperature range between 450 and 550 °C. Unfortunately the exponential dependence of the material degradation on the flue gas temperature also found within this work cannot be explained with the proposed corrosion mechanism. To determine the dominating corrosion mechanism, additionally test runs have been carried out in a specially designed drop tube reactor. To investigate the time-dependent corrosion behavior of 13CrMo4-5, a newly developed mass loss probe was applied under several constant parameter setups. In addition to these measurements, the time-dependent oxidation of 13CrMo4-5 under air was investigated in a muffle furnace. To gain relevant information regarding the corrosion mechanism prevailing, the deposits as well as the corrosion products have been examined subsequently to the test runs by means of scanning electron microscopy and energy dispersive X-ray analyses. With the experimental data gained it could be shown that the dominating corrosion mechanism strongly depends on the conditions prevailing (e.g., steel temperature, flue gas temperature, and velocity) and can either be the oxidation of the steel by gaseous O₂ and H₂O or a combination of oxidation and active Cl-induced oxidation.

In this paper, the activity of a cobalt/molybdenum (Co/Mo) commercial catalyst for the Water Gas Shift Reaction for hydrogen production was investigated in a three fixed-bed reactor pilot plant using a tar-rich synthesis gas from a full-scale biomass gasification plant as feed-stream. A parametric variation study was carried out to assess CO conversion (X_CO) and selectivity for the water gas shift reaction as a function of the operating temperature (T) in the range 300–450 °C. The effects of four dry gas hourly space velocities (GHSV), Case A-Case D, two steam to dry synthesis gas ratios (H₂O/SG), 56% v/v and 67% v/v, and a H₂S concentration in the range 100–220 ppm_v,db were investigated: the highest CO conversion (∼95%) was observed in the base case (Case A GHSV) at 67% v/v H₂O/SG, and 450 °C, the lower the operating temperature the lower the CO concentration, the lower the gas hourly space velocity the higher the CO conversion and the higher the H₂O/SG the higher the CO conversion. The effect of H₂S variation on CO conversion was also studied, keeping the operating temperature constant (≈365 °C) and using the Case D GHSV: CO conversion increased as the H₂S concentration increased and X_CO ≈ 40%. Selectivity was not influenced by the parameters investigated. Finally, the effect of the catalyst on tar removal was studied and a CO conversion close to 85% was found.

The crucial point in inorganic particle formation from biomass combustion is the temperature-dependent release of inorganic compounds, especially potassium (K). Currently, common wood fuels comprise of a comparatively low amount of K, but the increased usage of wood energy requires new feedstocks in the future. Potentially new feedstocks, such as short rotation coppice (SRC), fuels from agriculture (e.g., straw), or wood from broad-leafed trees of low rotation, contain usually high ash contents and/or high K concentrations. Apparently, these feedstocks will cause increased inorganic particle emissions from biomass combustion processes. The principle of a decreased firebed temperature as a primary measure aiming at a retention of K in the ashes of the firebed is a common approach for particle emission reduction and was investigated in several previous studies. The present study describes the usage of an ash-rich fuel from SRC pellets made from willow in a residential pellet boiler modified with an unique prototype of direct water-based firebed cooling. This test setup enables the study of the isolated impact of decreased firebed temperatures and its influence on the combustion process and emissions as well. A statistically significant effect of the firebed cooling on temperatures below the burner plate as on gaseous HCl and SO₂ was found. The high ash content of the used fuel limited the effectiveness of the applied direct firebed cooling in residential biomass combustion. The accumulation of a thick and thermal insulating ash layer above the burner plate decreased the heat transfer, limited the cooling efficiency, and revealed deviations from the expected particle formation process.