Publikationen

Other Publications | 2021

CO-lambda Optimierung - Betrieb von Biomassefeuerungen mit maximaler Effizienz und minimalen Emissionen

Zemann C. CO-lambda Optimierung - Betrieb von Biomassefeuerungen mit maximaler Effizienz und minimalen Emissionen. CO-lambda Optimierung - Betrieb von Biomassefeuerungen mit maximaler Effizienz und minimalen Emissionen. March 2021.

Details
Peer reviewed papers | 2021

Combustion of poultry litter and mixture of poultry litter with woodchips in a fixed bed lab-scale batch reactor

Katsaros G, Sommersacher P, Retschitzegger S, Kienzl N, Tassou SA, Pandey DS. Combustion of poultry litter and mixture of poultry litter with woodchips in a fixed bed lab-scale batch reactor. Fuel. 2021.286.119310.

External Link Details

Experiments have been conducted in a batch fixed bed lab-scale reactor to investigate the combustion behaviour of three different biomass fuels, poultry litter (PL), blend of PL with wood chips (PL/WC) and softwood pellets (SP). Analysis of the data gathered after completion of the test runs, provided useful insights about the thermal decomposition behaviour of the fuels, the formation of N gaseous species, the release of ash forming elements and the estimation of aerosol emissions. It was observed that the N gaseous species are mainly produced during the devolatilisation phase. Hydrogen cyanide (HCN) was the predominant compound in the case of SP combustion, whereas ammonia (NH3) displayed the highest concentration during the combustion of PL and blend (PL/WC). With reference to ash forming elements, the release rates of potassium (K) and sodium (Na) range between 15–50% and 20–37% respectively, whereas the release rate of sulphur (S) falls between 54–92%. Chlorine (Cl) presents very high release rate for all tested fuels acquiring values greater than 85%, showing the volatile nature of the specific compound. The maximum potential of aerosol emissions was estimated based on the calculation of ash forming elements. In particular, during PL combustion the maximum aerosol emissions were observed, 2806 mg/Nm3 (dry flue gas, 13 vol% O2), mainly influenced by the release rate of K in the gas phase. Fuel indexes for the pre-evaluation of combustion related challenges such as NOx emissions, potential for aerosols formation, corrosion risk, and ash melting behaviour have also been investigated.

Reports | 2021

Control of DHC networks and Reduction of the operating temperatures in DH systems

Task 55 Towards the Integration of Large SHC Systems into DHC Networks

Gölles M, Muschick D, Unterberger V, Leoni P, Schmidt R, Lennermo G. "Control of DHC networks and Reduction of the operating temperatures in DH systems". EA SHC FACTSHEET 55.A-D4.2. Date of Publication: 28.01.2021. https://task55.iea-shc.org/fact-sheets

External Link Details

Overview on different approaches for the control of the heat distribution networks in case of the integration of large-scale solar thermal systems, and different possibilities for the reduction of the operating temperatures in DH systems.

Reports | 2021

Control of large-scale solar thermal plants

Task 55 Towards the Integration of Large SHC Systems into DHC Networks

Gölles M, Unterberger V. "Control of large-scale solar thermal plants". IEA SHC FACTSHEET 55.B-D3.1. Date of Publication: 28.01.2021. https://task55.iea-shc.org/fact-sheets

External Link Details

Overview on the control of large-scale thermal plants, limited to plants feeding into DH networks as well as theirkey components, i.e. the actual collector circuit and the heat exchanger between primary and secondary circuit.

Peer reviewed papers | 2021

Correlations between tar content and permanent gases as well as reactor temperature in a lab-scale fluidized bed biomass gasifier applying different feedstock and operating conditions

von Berg L, Pongratz G, Pilatov A, Almuina-Villar H, Scharler R, Anca-Couce A. Correlations between tar content and permanent gases as well as reactor temperature in a lab-scale fluidized bed biomass gasifier applying different feedstock and operating conditions.Fuel.2021.305:121531

External Link Details

The major problem of fluidized bed biomass gasification is the high tar contamination of the producer gas which is associated with the complex and time-consuming sampling and analysis of these tars. Therefore, correlations to predict the tar content are a helpful tool for the development and operation of biomass gasifiers. Correlations between tars and gas composition as well as reactor temperature derived for a steam-blown lab-scale bubbling fluidized bed gasifier are investigated in this study to assess their applicability. A comprehensive data set containing over 80 experimental points was obtained for various operation conditions, including variations in temperature from 700 to 800 °C, feedstock, amount of steam for fluidization, as well as the addition of oxygen. Linear correlations between tar and permanent gases show good accuracy for H2 and CH4 when using pure steam. However, experiments conducted with steam-oxygen mixtures show high deviations for the CH4-based correlation and smaller but still significant deviations for the H2-based correlation. No relation between tar and CO or CO2 was found. The correlation between tar and temperature shows highest accuracy, including good agreement with the steam-oxygen experiments. All tar correlations showed useful results over a broad operating range. However, significant deviations can be obtained when considering just one gas compound. Therefore, a combination of different correlations considering gas components and temperature seems to be the best method of tar prediction. This leads to a powerful tool for fast online tar monitoring for a broad range of operating conditions, once a calibration measurement was conducted.

Peer reviewed papers | 2021

CPFD simulation of a dual fluidized bed cold flow model

Lunzer A, Kraft S, Müller S, Hofbauer H. CPFD simulation of a dual fluidized bed cold flow model. Biomass Conversion and Biorefinery. 2021. 11(1):189 - 203

External Link Details

The present work was carried out to simulate a cold flow model of a biomass gasification plant. For the simulation, a Eulerian-Lagrangian approach, more specifically the multi-phase particle in cell (MP-PIC) method, was used to simulate particles with a defined particle size distribution. Therefore, Barracuda VR, a software tool with an implemented MP-PIC method specifically designed for computational particle fluid dynamics simulations, was the software of choice. The simulation results were verified with data from previous experiments conducted on a physical cold flow model. The cold flow model was operated with air and bronze particles. The simulations were conducted with different drag laws: an energy-minimization multi-scale (EMMS) approach, a blended Wen-Yu and Ergun drag law, and a drag law of Ganser. The fluid dynamic behavior depends heavily on the particles’ properties like the particle size distribution. Furthermore, a focus was placed on the normal particle stress (PS value variation), which is significant in close-packed regions, and the loop seals’ fluidization rate was varied to influence the particle circulation rate. The settings of the simulation were optimized, flooding behavior did not occur in advanced simulations, and the simulations reached a stable steady state behavior. The Ganser drag law combined with an adjusted PS value with (PS = 30 Pa) or without (PS = 50 Pa) increased loop seal fluidization rates provided the best simulation results.

Peer reviewed papers | 2021

Dekarbonisierung in Salzburgs Skigebieten – Entwicklung von Optimierungsalgorithmen und Energiemanagementsystemen zur Steigerung der Energieeffizienz, Minimierung von Emissionen und Optimierung von Flexibilitäten [Decarbonization of the skiing areas in

Kritzer S, Passegger H, Ayoub T, Liedtke P, Zellinger M, Stadler M, Iglar B, Korner C, Aghaie H. Dekarbonisierung in Salzburgs Skigebieten – Entwicklung von Optimierungsalgorithmen und Energiemanagementsystemen zur Steigerung der Energieeffizienz, Minimierung von Emissionen und Optimierung von Flexibilitäten [Decarbonization of the skiing areas in Salzburg – development of optimization algorithms and energy management systems to increase energy efficiency, minimize emissions and optimize flexibility]. Elektrotechnik und Informationstechnik. 31 May 2021.

External Link Details

Winter tourism is an energy-intensive branch of industry. The aim of the FFG funding project Clean Energy for Tourism is to support Salzburg’s skiing areas on the way to decarbonization by developing technologies and business models. In this article, the developed ICT infrastructure, the optimization algorithms and the business models are presented.

Peer reviewed papers | 2021

Detailed NOX precursor measurements within the reduction zone of a novel small-scale fuel flexible biomass combustion technology

Archan G, Scharler R, Pölzer L, Buchmayr M, Sommersacher P, Hochenauer C, Gruber J, Anca-Couce A. Detailed NOX precursor measurements within the reduction zone of a novel small-scale fuel flexible biomass combustion technology. Fuel. 15 October 2021.302:121073

External Link Details

A novel biomass combustion technology with a compact fixed-bed operated with a low oxygen content and double air staging was investigated. Minimized flue gas emissions at high fuel flexibility were achieved only with primary measures. The fuel nitrogen conversion mechanisms were investigated in detail in the secondary zone of a 30 kW lab-reactor, designed as efficient reduction zone. Experimental investigations were carried out to determine the distribution of gas temperatures, main dry product gas components as well as NOX precursors such as NH3 and HCN along the height of the reduction zone. The objective was to determine and understand the various fuel nitrogen conversion mechanisms in the reduction zone that can minimize NOX emissions.

It was found that the HCN/NH3 ratio increases with the fuel nitrogen content. This corresponds to an unexpected opposite trend to typical biomass grate furnaces. It was concluded that it is crucial for the HCN/NH3 ratio whether the released nitrogen tars are already cracked in the fixed-bed or only in the gas phase, as in the novel technology. Furthermore, the influence of gas temperature, air ratio, mixing, recirculated flue gas and residence time on the formation and reduction of NH3, HCN and NO is discussed.

Finally, this novel technology achieves NOX emissions of<95 mg·m−3 and 175 mg·m−3 for woody and herbaceous fuels, respectively, which is well below the small-scale state-of-the-art for the respective N contents and it achieves fuel nitrogen conversions to NOX in flue gas of 35% and 25%, respectively.

Peer reviewed papers | 2021

Digestate as Sustainable Nutrient Source for Microalgae—Challenges and Prospects

Bauer L, Ranglová K, Masojidek J, Drosg B, Meixner K. Digestate as Sustainable Nutrient Source for Microalgae—Challenges and Prospects. Applied Sciences. 2021.11(3):1056

External Link Details

The interest in microalgae products has been increasing, and therefore the cultivation industry is growing steadily. To reduce the environmental impact and production costs arising from nutrients, research needs to find alternatives to the currently used artificial nutrients. Microalgae cultivation in anaerobic effluents (more specifically, digestate) represents a promising strategy for increasing sustainability and obtaining valuable products. However, digestate must be processed prior to its use as nutrient source. Depending on its composition, different methods are suitable for removing solids (e.g., centrifugation) and adjusting nutrient concentrations and ratios (e.g., dilution, ammonia stripping). Moreover, the resulting cultivation medium must be light-permeable. Various studies show that growth rates comparable to those in artificial media can be achieved when proper digestate treatment is used. The necessary steps for obtaining a suitable cultivation medium also depend on the microalgae species to be cultivated. Concerning the application of the biomass, legal aspects and impurities originating from digestate must be considered. Furthermore, microalgae species and their application fields are essential criteria when selecting downstream processing methods (harvest, disintegration, dehydration, product purification). Microalgae grown on digestate can be used to produce various products (e.g., bioenergy, animal feed, bioplastics, and biofertilizers). This review gives insight into the origin and composition of digestate, processing options to meet requirements for microalgae cultivation and challenges regarding downstream processing and products.

Peer reviewed papers | 2021

Drivers and barriers in retrofitting pulp and paper industry with bioenergy for more efficient production of liquid, solid and gaseous biofuels: A review.

Mäki E, Saastamoinen H, Melin K, Matschegg D, Pihkola H. Drivers and barriers in retrofitting pulp and paper industry with bioenergy for more efficient production of liquid, solid and gaseous biofuels: A review. Biomass and Bioenergy. 2021.106036. https://doi.org/10.1016/j.biombioe.2021.106036

External Link Details

Ample interest for more efficient utilization of bio-based residues has emerged in the Nordic pulp and paper (P&P) industry, which uses virgin wood as feedstock. Although different bioenergy retrofit technologies for production of liquid, solid, and gaseous bioenergy products have been applied in the existing P&P mills, the number of installations remains small. The lack of profound knowledge of existing bioenergy retrofits hinders the replication and market uptake of potential technologies. This review synthesises the existing knowledge of European installations and identifies the key drivers and barriers for implementation to foster the market uptake of potential technologies. The bioenergy retrofits were reviewed in terms of technical maturity, drivers, barriers and market potential. Based on this evaluation, common drivers and barriers towards wider market uptake were outlined from political, economic, social, technical, environmental, and legal perspective. Technologies already commercially applied include anaerobic fermentation of sludge, bark gasification, tall oil diesel and bioethanol production, whereas lignin extraction, biomethanol production, hydrothermal liquefaction and hydrothermal carbonization are being demonstrated or first applications are under construction. The findings of this review show that a stable flow of residues at P&P mills creates a solid base for retrofitting. New innovative bio-based products would allow widening the companies' product portfolios and creating new businesses. Also, European Union's (EU) legislation drives towards advanced biofuels production. Wider uptake of the retrofitting technologies requires overcoming the barriers related to uncertainty of economic feasibility and unestablished markets for new products rather than technical immaturity. 

Peer reviewed papers | 2021

Effect of biomass fuel ash and bed material on the product gas composition in DFB steam gasification

Fürsatz K, Fuchs J, Benedikt F, Kuba M, Hofbauer H. Effect of biomass fuel ash and bed material on the product gas composition in DFB steam gasification. Energy. 2021.219:119650.

External Link Details

Gasification is a thermochemical process that transforms carbonaceous matter into a gaseous secondary energy carrier, referred to as product gas. This product gas can be used for heat and power generation but also for syntheses. One possible gasification technology suitable for further synthesis is dual fluidised bed (DFB) steam gasification. The H2:CO ratio, which determines the suitability of the product gas for further synthesis, is influenced by the catalytic activity inside the gasification reactor. Eleven DFB steam gasification experiments were performed comparing the catalytic activity for various bed material and fuel combinations. The bed materials used were K-feldspar, fresh and layered olivine, and limestone, and the fuels gasified were softwood, chicken manure, a bark–chicken manure mixture and a bark-straw-chicken manure mixture. The water-gas-shift (WGS) equilibrium deviation was used to evaluate the catalytic activity inside the gasification reactor. It was shown that both the fuel ash and bed material have an effect on the catalytic activity during gasification. Scanning electron microscopy and energy dispersive X-ray spectrometry showed the initial layer formation for experiments with ash-rich fuels. Isolated WGS experiments were performed to further highlight the influence of bed material, fuel ash and fuel ash layers on the WGS equilibrium.

Conference presentations and posters | 2021

Effects of varying comminution techniques and pyrolysis temperatures on the particle shape of pyrolyzed wood powders and its implications on fluidisation behaviour

Deutsch R, Krammer G, Strasser C, Kienzl N. Effects of varying comminution techniques and pyrolysis temperatures on the particle shape of pyrolyzed wood powders and its implications on fluidisation behaviour. 29th European Biomass Conference and Exhibition, EUBCE 2021, 26-29 April 2021. 2021.

External Link Details

Iron production via blast furnace utilizes coal and coke to reduce iron oxides which results in high greenhouse gas emissions. Biomass-based reducing agents may reduce its fossil carbon footprint. Charcoal as bioreducer has been since the beginning of steelmaking. In order to obtain a reducing agent which is appropriately fluidizable for pulverized coal injection (PCI), the most influential powder characteristics must be named and the influence of thermal pre-treatment and comminution technique on particle properties have to be examined. The aim is to show that particle shape design of a grinding product is feasible to a certain extent by varying mill types and how pyrolyzed wood powder properties technically relevant for powder conveying processes can be influenced .

Peer reviewed papers | 2021

Emission minimization of a top-lit updraft gasifier cookstove based on experiments and detailed CFD analyses

Scharler R, Archan G, Rakos C, von Berg L, Lello D, Hochenauer C, Anca-Couce A. Emission minimization of a top-lit updraft gasifier cookstove based on experiments and detailed CFD analyses. Energy Conversion and Management. 2021.247:114755.

External Link Details

Around 2.7 billion people worldwide have no access to clean cooking equipment, which leads to major health problems due to high emissions of unburned products (VOC, CO and soot). A top-lit updraft gasifier cookstove with forced draft was identified as the technology with the highest potential for reducing harmful emissions from incomplete combustion in simple cookstoves. The basic variant of the stove was equipped with a fan for efficient mixing of product gas with air and fired with pellets to increase the energy density of low-grade residues. The development was conducted based on water boiling test experiments for wood and rice hull pellets and targeted CFD simulations of flow, heat transfer and gas phase combustion with a comprehensive description of the reaction kinetics, which were validated by the experiments. Emphasis was put on the reduction of CO emissions as an indicator for the burnout quality of the flue gas. The optimisation was carried out in several steps, the main improvements being the design of a sufficiently large post-combustion chamber and a supply of an appropriate amount of primary air for a more stable fuel gasification. The experiments showed CO emissions <0.2 g/MJdel for wood and rice hull pellets, which corresponds to a reduction by a factor of about 15 to 20 compared to the basic forced draft stove concept. Furthermore, these values are between 5 and 10 times lower than published water boiling test results of the best available cookstove technologies and are already close to the range of automatic pellet furnaces for domestic heating, which are considered to be the benchmark for the best possible reduction of CO emissions.

Reports | 2021

Endbericht: Heat Pumping system Control (HPC)

Modellbasierte Regelung von Absorptionswärmepump-Anlagen.

Zlabinger S, Wernhart M, Unterberger V, Rieberer R, Gölles M, Rohringer C, Poier H, Halmdienst C, Kemmerzehl C, Otto M. Heat Pumping system Control (HPC). Modellbasierte Regelung von Absorptionswärmepump-Anlagen. FFG, 4. Ausschreibung Energieforschungsprogramm, Projektnummer: 865095. Endbericht. 2021.

Download PDF Details
Reports | 2021

Energiespeicher in Österreich

Marktentwicklung 2020

Biermayr P, Aigenbauer St, Enigl M, Fink C, Knabl S, Leonhartsberger K, Matschegg D, Prem E, Strasser C, Wittmann M. Energiespeicher in Österreich Marktentwicklung 2020. 2021

External Link Details
Peer reviewed papers | 2021

Experimental evaluation of primary measures for NOX and dust emission reduction in a novel 200 kW multi-fuel biomass boiler

Archan G, Anca-Couce A, Buchmayr M, Hochenauer C, Gruber J, Scharler R. Experimental evaluation of primary measures for NOX and dust emission reduction in a novel 200 kW multi-fuel biomass boiler. June 2021.170:1186-1196. https://doi.org/10.1016/j.renene.2021.02.055

External Link Details

The aim of this work is to utilize various biogenic fuels without ash slagging and to significantly reduce NOX and particulate matter emissions in comparison to modern combustion technologies. For this purpose, a novel small-scale multi-fuel biomass grate furnace technology was developed and experimentally investigated. It employs a low oxygen concentration in the fixed-bed and a double air staging, including the supply of flue gas recirculation. In this way slagging is prevented on the grate, reducing the release of ash-forming volatiles, NOX emissions are minimized in the reduction zone and an efficient flue gas burnout is achieved in the tertiary zone. Wood pellets and chips as well as miscanthus briquettes were investigated.

The measured total particle emissions showed a reduction of 68% for pellets and 70% for wood chips compared to typical small-scale furnaces. Furthermore, a reduction of NOX emissions of 39% for wood chips, 40% for wood pellets and 45% for miscanthus briquettes was achieved compared to typical small-scale furnaces. The experimental parameter study provided fundamental insights into the various mechanisms involved in this novel technology, which is close to market introduction, and proved its high fuel flexibility and great potential for particulate matter and NOX emission reduction.

Peer reviewed papers | 2021

Fischer-Tropsch products from biomass-derived syngas and renewable hydrogen

Gruber H, Groß P, Rauch R, Reichhold A, Zweiler R, Aichernig C, Müller S, Ataimisch N, Hofbauer H. Fischer-Tropsch products from biomass-derived syngas and renewable hydrogen. Biomass Conversion and Biorefinery. 2021.11(6):2281-2292

External Link Details

Global climate change will make it necessary to transform transportation and mobility away from what we know now towards a sustainable, flexible, and dynamic sector. A severe reduction of fossil-based CO2 emissions in all energy-consuming sectors will be necessary to keep global warming below 2 °C above preindustrial levels. Thus, long-distance transportation will have to increase the share of renewable fuel consumed until alternative powertrains are ready to step in. Additionally, it is predicted that the share of renewables in the power generation sector grows worldwide. Thus, the need to store the excess electricity produced by fluctuating renewable sources is going to grow alike. The “Winddiesel” technology enables the integrative use of excess electricity combined with biomass-based fuel production. Surplus electricity can be converted to H2 via electrolysis in a first step. The fluctuating H2 source is combined with biomass-derived CO-rich syngas from gasification of lignocellulosic feedstock. Fischer-Tropsch synthesis converts the syngas to renewable hydrocarbons. This research article summarizes the experiments performed and presents new insights regarding the effects of load changes on the Fischer-Tropsch synthesis. Long-term campaigns were carried out, and performance-indicating parameters such as per-pass CO conversion, product distribution, and productivity were evaluated. The experiments showed that integrating renewable H2 into a biomass-to-liquid Fischer-Tropsch concept could increase the productivity while product distribution remains almost the same. Furthermore, the economic assessment performed indicates good preconditions towards commercialization of the proposed system.

Conference presentations and posters | 2021

Flue gas recirculation during poultry litter combustion in a fixed bed lab-scale batch reactor

Katsaros G, Sommersacher P, Retschitzegger S, Kienzl N, Pandey DS. Flue gas recirculation during poultry litter combustion in a fixed bed lab-scale batch reactor. 29th European Biomass Conference and Exhibition, EUBCE 2021, 26-29 April 2021. 2021

External Link Details

This study focuses on the combustion behaviour of poultry litter which was experimentally studied in a fixed bed lab-scale reactor. The combustion experiments not only provided useful insights pertaining to the thermal decomposition of poultry litter over time, release of main gaseous compounds and nitrogen (N) species, but also the release of elements found initially in the ash composition. The main gaseous species were released during the devolatilisation phase, whereas Ammonia (NH3) was found to be the most abundant compound of N-gaseous species (45%) followed by nitrogen oxide (NO) with a fraction of ~10%. Alkali metals showed moderate release rates, whilst Chlorine (Cl) was observed to have the highest one (90%) of the ash forming elements, depicting the high volatility of the specific compound.

Other Publications | 2021

Gasification - a key technology in the energy transition and for the circular economy

Martini S. Gasification - a key technology in the energy transition and for the circular economy. IEA Bioenergy Task33 Meeting. December 2021.

Details
Other Publications | 2021

Gemeinsam richtig heizen - Video

External Link Details
Other Publications | 2021

HPC - Workshop

Experimentelle Analyse, Simulation und Regelung von Absorptionswärmepumpen/-kältemaschinen

Zlabinger S, Unterberger V, Gölles M, Wernhart M, Rieberer R, Poier H, Rohinger C, Kemmerzehl C, Halmdienst C. Experimentelle Analyse, Simulation und Regelung von Absorptionswärmepumpen/-kältemaschinen. Online-Workshop im Rahmen des FFG-Projekts HPC ("4. Ausschreibung Energieforschung 2017") am 09.04.2021.

Download PDF Details

Durch die vermehrte Einbindung von Absorptionswärmepumpen und -kältemaschinen in bestehende und zukünftige Energiesysteme des Kälte- und Wärmesektors kann der Anteil erneuerbarer Energien deutlich gesteigert werden. Um dies erfolgreich umsetzen zu können, müssen die Betriebsstrategien und Regelungen dieser Systeme jedoch in der Lage sein, auch mit dynamischen und stark variierenden Betriebsbedingungen umgehen zu können. Dieser Herausforderung hat sich das von der FFG geförderte Projekt HPC – heat pumping system control gewidmet. Im Rahmen dieses Workshops sollen die Ergebnisse und deren Nutzen für die Praxis präsentiert und diskutiert werden.

Other papers | 2021

Increasing economic efficiency of cultivating microalgae by recycling process water

Neubauer M, Bauer L, Lanschützer E, Cayir P, Sonnleitner A, Meixner K, Fritz I, Drosg B. Increasing economic efficiency of cultivating microalgae by recycling process water. 29th European Biomass Conference and Exhibition, EUBCE 2021, 26-29 April 2021. 2021.

External Link Details

This abstract gives a glimpse of the output revealed in a project focusing on recycling used medium from algae cultivation. In close cooperation with the University of Natural Resources and Life Sciences Vienna, the Institute of Microbiology - The Czech Academy of Sciences as well as the algae biomass production company Ecoduna GmbH, it was possible to target industrial needs with scientific research approaches.

Peer reviewed papers | 2021

Influence of solvent temperature and type on naphthalene solubility for tar removal in a dual fluidized bed biomass gasification process

Tonpakdee P, Hongrapipat J, Siriwongrungson V, Rauch R, Pang S, Thaveesri J, Messner M, Kuba M, Hofbauer H. Influence of solvent temperature and type on naphthalene solubility for tar removal in a dual fluidized bed biomass gasification process. Current Applied Science and Technology. 2021.21(4):751-76.

External Link Details

Tar condensation is a cause of blockage in downstream application of the gasification process. An oil scrubber is considered as an effective method for tar removal. In this research, the naphthalene solubility in different local Thai oils and water was investigated in a laboratory-scale test-rig. The solubility value was conducted at 30, 50, 70, and 80°C. Biodiesels investigated were rapeseed methyl ester (RME) and two different palm methyl esters (PME 1 and PME 2). Furthermore, vegetable oils including sunflower oil, rice bran oil, crude palm oil, and refined palm oil were examined. The results showed that higher temperature enhanced naphthalene solubility in all types of investigated oils. Biodiesel has the highest value of naphthalene solubility. All scrubbing oils have similar naphthalene solubility trends at the temperature range of 50-80°C in the order of RME > PME 1 > PME 2 > diesel > sunflower oil > refined palm oil > rice bran oil > crude palm oil. Based on these experimental investigations, PME 1 has a naphthalene solubility value similar to RME. Therefore, PME 1 has been selected to be tested as scrubbing solvent in the 1 MWel prototype dual fluidized gasifier located in Nong Bua district, Nakhon Sawan province, Thailand.

Peer reviewed papers | 2021

Innovative laboratory unit for pre-testing of oxygen carriers for chemical-looping combustion

Fleiss B, Fuchs J, Penthor S, Arlt S, Pachler R, Müller S, Hofbauer H. Innovative laboratory unit for pre-testing of oxygen carriers for chemical-looping combustion. Biomass Conversion and Biorefinery. 2021

External Link Details

Chemical-looping combustion (CLC) is a highly efficient CO2 separation technology with no direct contact between combustion air and fuel. A metal oxide is used as an oxygen carrier (OC) and acts in a dual fluidized bed as a separation tool and supplies the fuel with oxygen, which as an oxidation medium causes combustion to CO2 and H2O. The use of solid fuels, especially biomass, is the focus of current investigations. The OC plays a key role, because it must meet special requirements for solid fuels, which are different to gaseous fuels. The ash content, special reaction mechanisms, and increased abrasion make research into new types of OC essential. Preliminary testing of OC before their use in larger plants regarding their suitability is recommended. For this reason, this work shows the design and the results of a laboratory reactor, which was planned and built for fundamental investigation of OC. Designed as a transient fluidized bed, the reactor, equipped with its own fuel conveying system and an in situ solid sampling, is intended to be particularly suitable for cheap and rapid pre-testing of OC materials. During the tests, it was shown that the sampling device enables non-selective sampling. Different OC were tested under various operating conditions, and their ability to convert different fuels could be quantified. The results indicate that OC can be sufficiently investigated to recommend operation in larger plants.

Peer reviewed papers | 2021

Integration of dual fluidized bed steam gasification into the pulp and paper industry

Kuba M, Benedikt F, Fürsatz K, Fuchs J, Demuth M, Aichernig C, Arpa L, Hofbauer H. Integration of dual fluidized bed steam gasification into the pulp and paper industry. Biomass Conversion and Biorefinery. 23 Dec 2021

External Link Details

The pulp and paper industry represents an industry sector which is characterised by its already high degree of sustainability. Biomass is a renewable input material, and typically highly developed recovery cycles minimise the loss of chemicals used in the pulping process. However, certain parts of the recovery cycle are still operated on fossil fuels. This study deals with the substitution of the fossil-based gaseous fuel with product gas from biomass gasification.

Gasification experiments have shown that bark available at pulp and paper mills is suitable to produce a product gas via dual fluidised bed steam gasification as a promising substitute for natural gas. Based on the comparison of process layouts regarding the separation of non-process elements, separation efficiency is derived for different setups. To ensure operational security of the chemical recovery cycle, comprehensive gas cleaning including heat exchangers, a particle filter, and a liquid scrubber unit is advised. The gas flow of fuel gas into the gas burner is increased as the heating value of the product gas is accordingly lower in comparison to natural gas. Furthermore, adaptions of the gas burner might be necessary to address the earlier ignition of the H2-rich product gas compared to natural gas.

Peer reviewed papers | 2021

Integration of market aspects into material development: approach and exemplification for a wood composite

Fuhrmann M, Schwarzbauer P, Hesser F. Integration of market aspects into material development: approach and exemplification for a wood composite. European Journal of Wood and Wood Products. 2021. https://doi.org/10.1007/s00107-021-01697-z

External Link Details

Due to a variety of applications and complex requirements in specific fields of use, the number of different materials is increasing. Thereof, the majority fails at the stage of market introduction, because the focus of material development is mostly on technical aspects, while market aspects are often neglected. One possible way of market introduction is material substitution. Thereby, requirements a material needs to meet are well known. However, a certain market focus on material development would be helpful regarding the final goal of the customer satisfaction. Therefore, this study presents an approach, which aims at guiding the technical material development and thus starts one stage earlier than most other studies, which focus on market introduction. A multi-stage approach helps integrating market aspects into material development, using the following methods: (1) method of Ashby to compare materials from a technical point of view and identify theoretically substitutable material groups and potential applications, (2) market data research and comparison for the identification of attractive markets, (3) method of Kano to classify material requirements and prioritize the optimization of material properties to satisfy the customers in selected markets. This approach is showcased and discussed using the example of an innovative wood composite under development, where it represented an aiding tool for guiding the further material development. An adaptation to any other material is possible at each of the three stages, although there are some limitations, which have to be considered, for example the selection of technical properties for the material comparison.

Peer reviewed papers | 2021

Interactions of Olivine and Silica Sand with Potassium- or Silicon-Rich Agricultural Residues under Combustion, Steam Gasification, and CO2 Gasification

Li G, Nathan GJ, Kuba M, Ashman PJ, Saw WL. Interactions of Olivine and Silica Sand with Potassium- or Silicon-Rich Agricultural Residues under Combustion, Steam Gasification, and CO2 Gasification. Industrial and Engineering Chemistry Research. 6 October 2021. 60 (39):14354 - 14369.

External Link Details

Interactions between olivine or silica sand and potassium (K)-rich grape marc or silicon (Si)-rich wheat straw were studied in a fixed-bed reactor under combustion, steam, or a CO2 gasification atmosphere. This study focused on the effects of atmosphere composition, feedstock, and bed material type on the thermochemical aspects of agglomeration. The agglomeration extent of grape marc with olivine as the bed material under air and steam atmospheres is significantly less than with silica sand. The presence of CO2, compared to that of O2 or steam, was found to promote the reaction between K and olivine by facilitating the production of reactive silica from olivine carbonization. The use of olivine promotes the release of K by more than 10% compared with silica. No significant differences were observed in the agglomeration extent of wheat straw in its interaction with either olivine or silica sand. Nevertheless, olivine alters the agglomeration mechanism of wheat straw to become “melting-induced” from “coating-induced” in a silica bed.

Peer reviewed papers | 2021

Interactions of Olivine and Silica Sand with Potassium- or Silicon-Rich Agricultural Residues under Combustion, Steam Gasification, and CO2Gasification

Li G, Nathan GJ, Kuba M, Ashman PJ, Saw WL. Interactions of Olivine and Silica Sand with Potassium- or Silicon-Rich Agricultural Residues under Combustion, Steam Gasification, and CO2Gasification. Industrial and Engineering Chemistry Research. 2021.60(39):14354-14369.

External Link Details

Interactions between olivine or silica sand and potassium (K)-rich grape marc or silicon (Si)-rich wheat straw were studied in a fixed-bed reactor under combustion, steam, or a CO2 gasification atmosphere. This study focused on the effects of atmosphere composition, feedstock, and bed material type on the thermochemical aspects of agglomeration. The agglomeration extent of grape marc with olivine as the bed material under air and steam atmospheres is significantly less than with silica sand. The presence of CO2, compared to that of O2 or steam, was found to promote the reaction between K and olivine by facilitating the production of reactive silica from olivine carbonization. The use of olivine promotes the release of K by more than 10% compared with silica. No significant differences were observed in the agglomeration extent of wheat straw in its interaction with either olivine or silica sand. Nevertheless, olivine alters the agglomeration mechanism of wheat straw to become “melting-induced” from “coating-induced” in a silica bed.

Other Publications | 2021

Leitfaden: Energiegemeinschaften im Tourismussektor

Iglar B, Fina B, Jung M, Markotsky-Kolm E, Tölzer T, Zellinger M, Liedtke P, Oberbauer C. Leitfaden: Energiegemeinschaften im Tourismussektor. Klima- und Energiefonds. December 2021.

Details
Peer reviewed papers | 2021

Mixed-integer linear programming based optimization strategies for renewable energy communities

Cosic A, Stadler M, Mansoor M, Zellinger M. Mixed-integer linear programming based optimization strategies for renewable energy communities. Energy. 237.2021

External Link Details

Local and renewable energy communities show a high potential for the efficient use of distributed energy technologies at regional levels according to the Clean Energy Package of the European Union. However, until now there are only limited possibilities to bring such energy communities into reality because of several limitation factors. Challenges are already encountered during the planning phase since a large number of decision variables have to be considered depending on the number and type of community participants and distributed technologies. This paper overcomes these challenges by establishing a mixed-integer linear programming based optimal planning approach for renewable energy communities. A real case study is analyzed by creating an energy community testbed with a leading energy service provider in Austria. The case study considers nine energy community members of a municipality in Austria, distributed photovoltaic systems, energy storage systems, different electricity tariff scenarios and market signals including feed-in tariffs. The key results indicate that renewable energy communities can significantly reduce the total energy costs by 15% and total carbon dioxide emissions by 34% through an optimal selection and operation of the energy technologies. In all the optimization scenarios considered, each community participant can benefit both economically and ecologically.

Peer reviewed papers | 2021

Model-Based Estimation of the Flue Gas Mass Flow in Biomass Boilers.

Niederwieser H, Zemann C, Goelles M, Reichhartinger M. Model-Based Estimation of the Flue Gas Mass Flow in Biomass Boilers. IEEE Transactions on Control Systems Technology. 2021 Jul;19(4):1609 - 1622. https://doi.org/10.1109/TCST.2020.3016404

External Link Details

Three estimators for the estimation of the flue gas mass flow in biomass boilers are presented and compared, namely a sliding-mode observer, a Kalman filter, and a so-called steady-state estimator. The flue gas mass flow is an important process variable in biomass boilers as it contains information about the supplied mass flows of air and decomposed fuel. It is also related to the generated heat flow. Furthermore, its knowledge may be exploited in model-based control strategies which allow one to keep pollutant emissions low, on the one hand, and to achieve high efficiency, on the other hand. However, due to fouling of the equipment over time, measurements and existing estimation methods are not suitable for long-term applications. The estimators proposed in this article are based on a dynamic model for gas tube heat exchangers. They are capable of handling the fouling of the heat exchanger and, additionally, they offer the possibility of monitoring the degree of fouling. By incorporating an additional differential pressure measurement and extending the aforementioned estimators, an improvement regarding the dynamic response and the estimation accuracy is achieved. The application of the estimators to real measurement data from both, a medium-scale and a small-scale biomass boiler, demonstrates their wide applicability.

PhD Thesis | 2021

Modelling and control of large-scale solar thermal systems

Unterberger V. Modelling and control of large-scale solar thermal systems. 2021. 212 p.

Details

Heat makes up the largest share of energy end-use, accounting for 50% of global final energy consumption in 2018 and contributing to about 40% of global carbon dioxide (CO2) emissions. Of the total heat produced, about 46% was consumed in buildings for space and water heating. Large-scale solar thermal systems provide a highly valuable possibility to increase the share of renewables in heating systems and to reduce carbon dioxide emissions. In this context, the worldwide number of large-scale solar heating systems has increased rapidly in the last couple of years, especially in China and European countries, e.g. in Denmark. This has led to the installation of about 400 large-scale solar thermal systems ( ≥ 350kWth, 500m²) by the end of 2019.
Unlike other heating systems, their main source of power (solar radiation) cannot be manipulated and is subject to changes on a seasonal as well as on a daily basis. That is why control systems play a very important role for the efficient operation of these systems. This thesis therefore focuses on the application of model-based control strategies, and the necessary preliminary work regarding modelling, in order to achieve an efficient control of large-scale solar thermal systems. Consequently, the thesis addresses three important aspects:
In the first main section, models of components of large-scale solar thermal systems are developed and validated. For the most important components (heat exchanger, solar collector and sensible heat storage), two models of different complexity, one simulation-oriented, one control-oriented, are developed. While the simulation-oriented models aim to model the physical behaviour very accurately in order to be used in simulation studies, control-oriented models aim to model the physical behaviour only as accurately as necessary in order to serve as a basis for model-based control strategies. All models are validated with measurement data from a typical solar system, and it is shown that they are sufficiently accurate for their intended purpose. The sum of the models provides a holistic view on all modelling aspects that have to be considered in large-scale solar thermal plants, and serves as a reasonable basis for model-based control strategies and accurate simulation studies of solar systems.
In the second main section, adaptive forecasting methods for the future solar heat production as well as the heat demand are developed and validated with measurement data and using real weather forecasts. These methods are important to most efficiently integrate and operate solar systems by better scheduling heat production, storage and distribution for the near future. In order to be used in real-world applications, the methods are developed with the goal to meet three important practical requirements: simple implementation, automatic adaption to seasonal changes, and wide applicability. The final long-term evaluation for half a year proves that the developed methods can forecast the solar heat production as well as the heat demand very accurately and outperform common forecasting methods, yielding results that are nearly twice as accurate.
In the third main section, model-based control strategies for the high-level as well as for the low-level control of solar thermal systems are developed and validated. For the high-level control an approach is presented which considers future information by using the developed forecasting methods. It achieves higher profits (plus 3 %) and leads to a more stable operation, compared to the existing commercial solution. For the low-level control, model-based control strategies based on the developed models for the heat generation and distribution are presented. The model-based control strategy for the heat generation considers the dynamic behaviour of the collector and especially considers the variable time-delay. This, compared to conventional control strategies, leads to a significantly better control performance in case of fluctuating solar radiation and changing inlet temperatures. The model-based control strategy for the heat distribution follows a modular approach which can be applied for several hydraulic settings, leading to an accurate and independent control of mass flow and temperature, and outperforms state-of-the-art control strategies. For both control levels, care was taken that the applied strategies can be used in real-world applications regarding their mathematical complexity and computational resources required.
In summary, this thesis presents a holistic approach regarding modelling (simulation-oriented models, control-oriented models and adaptive forecasting methods) and control aspects (high-level as well as low-level control) which can help to improve the efficiency of large-scale solar thermal plants on various levels, making them more competitive, and is furthermore essential for a successful integration of these plants in larger energy systems.

Peer reviewed papers | 2021

Modelling fuel flexibility in fixed-bed biomass conversion with a low primary air ratio in an updraft configuration

Anca-Couce A, Archan G, Buchmayr M, Essl M, Hochenauer C, Scharler R. Modelling fuel flexibility in fixed-bed biomass conversion with a low primary air ratio in an updraft configuration. Fuel. 2021.296:120687.

External Link Details

Fixed-bed biomass conversion with a low primary air ratio and a counter-current configuration has a high feedstock flexibility, as it resembles updraft gasification, and the potential to reduce emissions when integrated in biomass combustion systems. A 1D bed model was validated with experimental results from a biomass combustion boiler with such a bed conversion system, predicting with a good accuracy the temperatures in the reactor and producer gas composition. The model was applied for different cases to investigate the fuel flexibility of this combustion system, including the influence of moisture content and the maximum temperatures achieved in the bed. It was shown that with variations in fuel moisture content from 8 to 30% mass w.b. the producer gas composition, char reduction to CO or maximum temperatures at the grate were not affected due to the separation of the char conversion and pyrolysis/drying zones. Flue gas recirculation was the only possible measure with the tested configuration to reduce the maximum temperatures close to the grate, which is beneficial e.g. to avoid slagging with complicated fuels. A higher tar content was obtained than in conventional updraft gasifiers, which is attributed to the absence of tar condensation in the bed due to the limited height of the reactor and the integration in the combustion chamber. The presented model can support the development of such combustion technologies and is a relevant basis for detailed CFD simulations of the bed or gas phase conversion.

Peer reviewed papers | 2021

Operation of coupled multi-owner district heating networks via distributed optimization

Kaisermayer V, Muschick D, Horn M, Gölles M. Operation of coupled multi-owner district heating networks via distributed optimization. Energy Reports. 2021 Okt;7(Suppl. 4):273-281. https://doi.org/10.1016/j.egyr.2021.08.145

External Link Details

The growth of district heating and cooling (DHC) networks introduces the possibility of connecting them with neighbouring networks. Coupling networks can save costs by reducing operating hours of peak load or backup boilers, or free up production capacity for network expansion. Optimization-based energy management systems (EMS) already provide operators of individual DHC networks with solutions to the unit commitment and economic dispatch problem. They are especially useful for complex networks with multiple producers and integrated renewable energy sources, where incorporating forecasts is important. Time-dependent constraints and network capacity limitations can easily be considered. For coupled networks, a centralized optimization would provide a minimum with respect to an objective function which can incorporate fuel costs, operational costs and costs for emissions. However, the individual coupled networks are generally owned by different organizations with competing objectives. The centralized solution might not be accepted, as each company aims to optimize its own objective. Additionally, all data has to be shared with a centralized EMS, and it represents a single point of failure. A decentralized EMS may therefore be a better choice in a multi-owner setting. In this article, a novel decentralized EMS is presented that can handle multi-owner structures with cooperative and non-cooperative coupling. Each local EMS solves its own optimization problem, and an iterative Jacobi-style algorithm ensures consensus among the networks. The distributed EMS is compared to a centralized EMS based on a representative real-world example consisting of three coupled district heating networks operated by two companies.

Other Publications | 2021

Operation of Coupled Multi-Owner District Heating Networks via Distributed Optimization

Muschick D, Gölles M, Kaisermayer V, Horn M. Operation of Coupled Multi-Owner District Heating Networks via Distributed Optimization.17th International Symposium on District Heating and Cooling. Nottingham Trent University, Nottingham, United Kingdom. 7. Sep 2021. Oral Presentation. [online]

Download PDF Details

The simultaneous operation of multiple connected heating networks can be handled by optimization techniques. However, a global optimum might not represent a good operating strategy if the networks belong to different owners and thus might habe competing interests. An approach from game theory then needs to be applied, which finds a generalized Nash equilibrium instead.

Reports | 2021

OptEnGrid Optimal integration of heat, electricity and gas systems to increase efficiency and reliability

Download PDF Details

OptEnGrid is a cross-sectoral multi-energy system optimization tool for the optimal planning and dispatch of the Distributed Energy Resource (DER) technologies in smart- and microgrids. The methodology of OptEnGrid considers an optimization model which is based on Mixed-Integer Linear Programming (MILP) framework. The following sub-sections provide more details about the energy flow and system optimization inside OptEnGrid and the choice of the optimization over simulation

Other Publications | 2021

Optimal operation of cross-ownership district heating and cooling networks

Muschick D, Kaisermayer V, Gölles M, Horn M.Optimal operation of cross-ownership district heating and cooling networks. 20th European Roundtable on Sustainable Consumption and Production. 9. Sep 2021. Graz. Oral Presentation.

Download PDF Details
Peer reviewed papers | 2021

Optimal planning of thermal energy systems in a microgrid with seasonal storage and piecewise affine cost functions

Mansoor M, Stadler M, Zellinger M, Lichtenegger K, Auer H, Cosic A. Optimal planning of thermal energy systems in a microgrid with seasonal storage and piecewise affine cost functions. Energy. 2021:215;119095.

External Link Details

The optimal design of microgrids with thermal energy system requires optimization techniques that can provide investment and scheduling of the technology portfolio involved. In the modeling of such systems with seasonal storage capability, the two main challenges include the low temporal resolution of available data and the non-linear cost versus capacity relationship of solar thermal and heat storage technologies. This work overcomes these challenges by developing two different optimization models based on mixed-integer linear programming with objectives to minimize the total energy costs and carbon dioxide emissions. Piecewise affine functions are used to approximate the non-linear cost versus capacity behavior. The developed methods are applied to the optimal planning of a case study in Austria. The results of the models are compared based on the accuracy and real-time performance together with the impact of piecewise affine cost functions versus non-piecewise affine fixed cost functions. The results show that the investment decisions of both models are in good agreement with each other while the computational time for the 8760-h based model is significantly greater than the model having three representative periods. The models with piecewise affine cost functions show larger capacities of technologies than non-piecewise affine fixed cost function based models.

Reports | 2021

Planung zellularer Energiesysteme

Teil 1: Effektive integrierte Investitions- und Betriebsplanung von Energiezellen

VDE Verband der Elektrotechnik e.V. Energietechnische Gesellschaft (ETG)

External Link Details

In einem zellularen Energiesystem wird die physikalische Balance zwischen Energieangebot und -nachfrage so weit als möglich bereits auf regionaler, lokaler Ebene hergestellt. Der zentrale Baustein dabei ist die Energiezelle. Sie kann Energie in Form von Wärme, Elektrizität oder Gas aufnehmen und/oder Elektrizität und Wärme (z. B. aus erneuerbaren Energien) selbst erzeugen, um so den eigenen Wärme- und Elektrizitätsbedarf zu decken. Energieüberschüsse können (elektrisch und/oder thermisch) gespeichert oder anderen Zellen im Nahbereich oder einem Energieversorger zur Verfügung gestellt werden. Ein Energiezellenmanagement kann in Koordination mit Nachbarzellen den Ausgleich von Erzeugung und Verbrauch über alle vorhandenen Energieformen organisieren.
Die Planung und der Betrieb zellularer Energiesysteme ist eine komplexe Aufgabe, da eine Vielzahl von dezentralen Energietechnologien, verschiedenste Ziele und auch Entscheidungsträger berück-sichtigt werden müssen.
Der vorliegende VDE Impuls beschreibt als ersten Schritt die Planung einer Energiezelle, welche mit Energieversorgern interagieren kann. Er ist der Auftakt einer Reihe weiterer Veröffentlichungen zur detaillierten Planung von Energiezellen und zellularen Energiesystemen.

Conference presentations and posters | 2021

Price cointegration in the Austrian sawmill industry with a focus on by-products

Fuhrmann M, Dißauer C, Strasser C, Schmid E. Price cointegration in the Austrian sawmill industry with a focus on by-products. 29th European Biomass Conference and Exhibition, EUBCE 2021. 26-29 April 2021.

Details
Other Publications | 2021

Probenahmen, Messung, Behandlung von Chrom VI in Holzaschen

Retschitzegger S. Probenahmen, Messung, Behandlung von Chrom VI in Holzaschen. 23. Österreichischer Biomassetag & Heizwerke-Betreibertag. September 2021.

Details
Other Publications | 2021

Raising awareness and changing behaviour with the traveling combustion education - The CleanAir II project

Schwabl M. Raising awareness and changing behaviour with the traveling combustion education - The CleanAir II project. IEA Bioenergy End-of-Triennium Conference. December 2021.

Details
Peer reviewed papers | 2021

Real-life emissions from residential wood combustion in Austria: From TSP emissions to PAH emission profiles, diagnostic ratios and toxic risk assessment

B Kirchsteiger, F Kubik, R Sturmlechner, H Stressler, M Schwabl, M Kistler, A Kasper-Giebl. Real-life emissions from residential wood combustion in Austria: From TSP emissions to PAH emission profiles, diagnostic ratios and toxic risk assessment. Atmospheric Pollution Research. 2021.12:8.

External Link Details

Residential wood combustion is, besides particulate emissions, also linked to emissions of organic compounds, comprising various toxic substances such as polycyclic aromatic hydrocarbons (PAHs). Although, literature data has shown that highest emissions occur during maloperations caused by the user itself, most studies focus on lab-testing not reflecting the situation in the field. This study evaluates the real-life situation in Austria, investigating emissions of total suspended particles (TSP) and particle-bound substances of four manually operated room heaters commonly installed in people's homes. Measurements were conducted within a field measurement campaign realized in the scope of the Clean Air by biomass project. To evaluate the impact of the users' habit two types of combustion experiments were performed, one representing the diversity of possible maloperations and one realized under optimized conditions following a strict optimization protocol. As special focus was laid on PAHs, sampling was realized using a dilution system adapted for the use in the field. Generally, optimization lead to a clear decrease of most compounds (i.e. TSP, OC, EC, PAHs), however, emissions of the anhydrosugar levoglucosan were not affected at all. Total PAH emissions could be clearly reduced, moreover, optimization lead to a shift towards low molecular weight PAHs and thus, less toxic ones, clearly reflected by lower toxicity equivalents. Correlation analysis using the Spearman's rank method showed significantly high correlations among the individual PAH congeners, and rather low ones with other target substances.

Peer reviewed papers | 2021

Single Pellet Combustion of Sewage Sludge and Agricultural Residues with a Focus on Phosphorus

Häggström G, Hannl TK, Hedayati A, Kuba M, Skoglund N, Öhman M. Single Pellet Combustion of Sewage Sludge and Agricultural Residues with a Focus on Phosphorus. Energy & Fuels. 8 June 2021.

External Link Details

Recycling of phosphorus in combination with increased utilization of bioenergy can mitigate material and global warming challenges. In addition, co-combustion of different fuels can alleviate ash-related problems in thermal conversion of biomass. The aim of this study is to investigate the ash transformation reactions of mainly P in co-combustion of P-rich sewage sludge (SS) with K-rich sunflower husks (SH) and K- and Si-rich wheat straw (WS). Single pellets of 4 mixtures (10 and 30 wt % SS in WS and 15 and 40 wt % SS in SH) and pure SS were combusted in an electrically heated furnace at process temperatures relevant for fluidized bed combustion (800 and 950 °C). Collected ash fractions were analyzed by inductively coupled plasma techniques, ion chromatography, scanning electron microscopy–energy-dispersive X-ray spectroscopy, and X-ray diffraction. Thermodynamic equilibrium calculations were performed to interpret the results. Over 90% of K and P was found to be captured within the residual ash with 30–70% P in crystalline K-bearing phosphates for mixtures with low amounts of SS (WSS10 and SHS15). The significant share of K and P in the amorphous material could be important for P recovery. For the lower percentage mixtures of SS (WSS10 and SHS15), P in crystalline phases was mainly found in K-whitlockite and CaKPO4. For the higher percentage SS mixtures, most of P was found in whitlockites associated with Fe and Mg, and no crystalline phosphates containing K were detected. For P recovery, co-combustion of the lower SS mixtures is favorable, and they are suggested to be further studied concerning the suitability for plant growth.

Peer reviewed papers | 2021

Steam gasification of biomass – Typical gas quality and operational strategies derived from industrial-scale plants

Larsson A, Kuba M, Berdugo Vilches T, Seemann M, Hofbauer H, Thunman H. Steam gasification of biomass – Typical gas quality and operational strategies derived from industrial-scale plants. Fuel Processing Technology. 2021.212:106609.

External Link Details

Steam gasification enables the thermochemical conversion of solid fuels into a medium calorific gas that can be utilized for the synthesis of advanced biofuels, chemicals or for heat and power production. Dual fluidized bed (DFB) gasification is at present the technology applied to realize gasification of biomass in steam environment at large scale. Few large-scale DFB gasifiers exist, and this work presents a compilation and analysis of the data and operational strategies from the six DFB gasifiers in Europe. It is shown that the technology is robust, as similar gas quality can be achieved despite the differences in reactor design and operation strategies. Reference concentrations of both gas components and tar components are provided, and correlations in the data are investigated. In all plants, adjusting the availability and accessibility to the active ash components (K and Ca) was the key to control the gas quality. The gas quality, and in particular the tar content of the gas, can conveniently be assessed by monitored the concentration of CH4 in the produced gas. The data and experience acquired from these plants provide important knowledge for the future development of the steam gasification of biomass.

Reports | 2021

Supervisory control of large-scale solar thermal systems

Task 55 Towards the Integration of Large SHC Systems into DHC Networks

Gölles M, Unterberger V, Kaisermayer V, Nigitz T, Muschick D. "Supervisory control of large-scale solar thermal systems". IEA SHC FACTSHEET 55.A-D4.1. Date of Publication: 28.01.2021. https://task55.iea-shc.org/fact-sheets

External Link Details

Overview on different approaches for supervisory control strategies,deciding on operating modes and set points for the controls of the different plants and componentsintegrated in solar thermal systems.

Reports | 2021

Tailoring of the pore structures of wood pyrolysis chars for potential use in energy storage applications

Maziarka P, Sommersacher P, Wang X, Kienzl N, Retschitzegger S, Prins W, Hedin N, Ronsse F. Tailoring of the pore structures of wood pyrolysis chars for potential use in energy storage applications. Applied Energy.2021.286:116431. https://doi.org/10.1016/j.apenergy.2020.116431

External Link Details

Char obtained from biomass pyrolysis is an eco-friendly porous carbon, which has potential use as a material for electrodes in supercapacitors. For that application, a high microporous specific surface area (SSA) is desired, as it relates to the accessible surface for an applied electrolyte. Currently, the incomplete understanding of the relation between porosity development and production parameters hinders the production of tailor-made, bio-based pyrochars for use as electrodes. Additionally, there is a problem with the low reliability in assessing textual properties for bio-based pyrochars by gas adsorption. To address the aforementioned problems, beech wood cylinders of two different lengths, with and without pre-treatment with citric acid were pyrolysed at temperatures of 300–900 °C and analysed by gas adsorption. The pyrolyzed chars were characterised with adsorption with N2 and CO2 to assess the influence of production parameters on the textual properties. The new approach in processing the gas adsorption data used in this study demonstrated the required consistency in assessing the micro- and mesoporosity. The SSA of the chars rose monotonically in the investigated range of pyrolysis temperatures. The pre-treatment with citric acid led to an enhanced SSA, and the length of the cylinders correlated with a reduced SSA. With pyrolysis at 900 °C, the micro-SSAs of samples with 10 mm increased by on average 717 ± 32 m2/g. The trends among the investigated parameters and the textual properties were rationalized and provide a sound basis for further studies of tailor-made bio-based pyrochars as electrode materials in supercapacitors.

Peer reviewed papers | 2021

Techno-economic optimization of islanded microgrids considering intra-hour variability

Mathiesen P, Stadler M, Kleissl J, Pecenak Z. Techno-economic optimization of islanded microgrids considering intra-hour variability. Applied Energy. 2021.304:117777.

External Link Details

The intra-hour intermittency of solar energy and demand introduce significant design challenges for microgrids. To avoid costly energy shortfalls and mitigate outage probability, islanded microgrids must be designed with sufficient distributed energy resources (DER) to meet demand and fulfill the energy and power balance. To avoid excessive runtime, current design tools typically only utilize hourly data. As such, the variable nature of solar and demand is often overlooked. Thus, DER designed based on hourly data may result in significant energy shortfalls when deployed in real-world conditions. This research introduces a new, fast method for optimizing DER investments and performing dispatch planning to consider intra-hour variability. A novel set of constraints which operate on intra-hour data are implemented in a mixed-integer-linear-program microgrid investment optimization. Variability is represented by the single worst-case intra-hour fluctuation. This allows for fast optimization times compared to other approaches tested. Applied to a residential microgrid case study with 5-minute intra-hour resolution, this new method is shown to maintain optimality within 2% and reduce runtime by 98.2% compared to full-scale-optimizations which consider every time-step explicitly. Applicable to a variety of technologies and demand types, this method provides a general framework for incorporating intra-hour variability into microgrid design.

Other papers | 2021

The robust exact differentiator toolbox revisited: Filtering and discretization features.

Andritsch B, Horn M, Koch S, Niederwieser H, Wetzlinger M, Reichhartinger M. The robust exact differentiator toolbox revisited: Filtering and discretization features. in 2021 IEEE International Conference on Mechatronics, ICM 2021. Institute of Electrical and Electronics Engineers. 2021. 9385675 https://doi.org/10.1109/ICM46511.2021.9385675

External Link Details

An extended version of a Simulink ® -block providing on-line differentiation algorithms based on discretized sliding-mode concepts is presented. Based on user-specified settings it computes estimates of the time-derivatives of the input signal up to order ten. Different discrete-time estimation algorithms as well as optional filtering properties can be selected. The paper includes an overview of the implemented algorithms, a detailed explanation of the developed Simulink ® -block and two examples. The first example illustrates the application of the toolbox in a numerical simulation environment whereas the second one shows results obtained via an electrical laboratory setup.

Peer reviewed papers | 2021

Ultra-low temperature water-gas shift reaction catalyzed by homogeneous Ru-complexes in a membrane reactor - membrane development and proof of concept

Logemann M, Wolf P, Loipersböck J, Schrade A, Wessling M, Haumann M. Ultra-low temperature water-gas shift reaction catalyzed by homogeneous Ru-complexes in a membrane reactor - membrane development and proof of concept. Catalysis Science and Technology. 2021.11(4):1558-1570. https://doi.org/10.1039/D0CY02111C

External Link Details

A monolithic membrane reactor combining the supported ionic liquid-phase (SILP) catalyzed ultra-low temperature water–gas shift reaction (WGSR) with in situ product removal is presented. The SILP catalyst consists of the transition metal complex [Ru(CO)3Cl2]2 homogeneously dissolved in 1-butyl-2,3-dimethylimidazolium chloride [C4C1C1Im]Cl and supported on alumina pellets. These Ru-SILP pellets are deposited inside the channels of a silicon carbide monolith. The resulting monolithic catalyst is very active and stable in the WGSR in the temperature range between 120 and 160 °C, thereby making full use of the high equilibrium conversion at these conditions. A facilitated transport membrane was coated onto the smooth outside of the SiC monolith to allow preferential removal of CO2 compared to H2. The proof of this concept has been shown under industrially relevant conditions using a biogas feed. These results demonstrate, for the first time, the combination of homogeneous SILP catalyzed WGSR with enhanced in situ removal of one of the products (here: CO2) via facilitated transport membrane separation.

Peer reviewed papers | 2021

Valorisation of starch wastewater by anaerobic fermentation

Drosg B, Neubauer M, Marzynski M, Meixner K. Valorisation of starch wastewater by anaerobic fermentation. Applies Sciences (Switzerland). 2021.11(21):10482.

External Link Details

Starch production is mainly focused on feedstocks such as corn, wheat and potato in the EU, whereas cassava, rice, and other feedstocks are utilised worldwide. In starch production, a high amount of wastewater is generated, which accumulates from different process steps such as washing, steeping, starch refining, saccharification and derivatisation. Valorisation of these wastewaters can help to improve the environmental impact as well as the economics of starch production. Anaerobic fermentation is a promising approach, and this review gives an overview of the different utilisation concepts outlined in the literature and the state of the technology. Among bioenergy recovery processes, biogas technology is widely applied at the industrial scale, whereas biohydrogen production is used at the research stage. Starch wastewater can also be used for the production of bulk chemicals such as acetone, ethanol, butanol or lactic acids by anaerobic microbes.

PhD Thesis | 2022

A control strategy for optimising the operational behaviour of biomass boilers

Zemann C. A control strategy for optimising the operational behaviour of biomass boilers. 2022. 225 S.

Details

Biomassefeuerungen spielen eine Schlüsselrolle in der Energiewende hin zu einem vollständig erneuerbaren Energiesystem. Allerdings müssen sie sich zukünftigen Herausforderungen stellen, um weiterhin relevant zu bleiben. Einerseits müssen Biomassefeuerungen mit dem höchstmöglichen Wirkungsgrad arbeiten, um wirtschaftlich rentabel zu bleiben während sie gleichzeitig eine hohe Lastmodulationsfähigkeit aufweisen müssen, um für eine breitere Palette von Anwendungen eingesetzt werden zu können. Andererseits müssen Biomassefeuerungen immer strengere Grenzwerte für Schadstoffemissionen einhalten und gleichzeitig in der Lage sein, neue und alternative Biomassebrennstoffe mit geringerer Qualität zu verbrennen.

In dieser Arbeit wird eine modellbasierte Regelungsstrategie entwickelt, die es Biomassefeuerungen ermöglicht, all diese Herausforderungen zu meistern. Diese Regelungsstrategie besteht aus drei Teilen, einer Verbrennungsregelung, einem Zustands- und Parameterschätzer und einer Methode zur CO-lambda-Optimierung. Alle drei Teile werden in dieser Arbeit hergeleitet und im Detail diskutiert, insbesondere im Hinblick auf ihre Implementierung an realen Biomassefeuerungen. Darüber hinaus werden alle drei Teile der modellbasierten Regelungsstrategie durch Simulationsstudien sowie durch eine Implementierung in realen Biomassefeuerungen verifiziert.

Als Grundlage für die modellbasierte Regelungsstrategie wird ein mathematisches Modell abgeleitet, welches das dynamische Verhalten der Prozesse in der Biomassefeuerungen einschließlich des Einflusses der Brennstoffeigenschaften beschreibt. Die berücksichtigten Brennstoffeigenschaften sind die Schüttdichte und die chemische Zusammensetzung einschließlich des Wasser- und Aschegehalts sowie der untere Heizwert.

Die Verbrennungsregelung nutz die Stellglieder der Biomassefeuerung um dessen stabilen Betrieb zu gewährleisten und schnelle Laständerungen zu ermöglichen. Diese modellbasierte Regelstrategie berücksichtigt durch ihre Formulierung, die auf dem oben genannten mathematischen Modell basiert, explizit alle relevanten Brennstoffeigenschaften. Dadurch reagiert sie gezielt auf Änderungen dieser Brennstoffeigenschaften und kompensiert direkt deren Einfluss auf den Betrieb der Biomassefeuerung. Gleichzeitig weist sie eine einfache Struktur auf und ist daher leicht zu implementieren und zu warten. Diese modellbasierte Verbrennungsregelung wird sowohl in Simulationsstudien als auch durch Experimente nach einer Implementierung an einer realen Biomassefeuerung verifiziert.

Es wird ein kombinierter Zustands- und Parameterschätzer entwickelt, der gleichzeitig die Brennstoffeigenschaften, die anschließend von der Verbrennungsregelung verwendet werden, und die Zustandsgrößen der Biomassefeuerungen in Echtzeit schätzt. Er basiert auf einem erweiterten Kalman-Filter, der das in dieser Arbeit vorgestellte mathematische Modell verwendet. Diese Methode wird für verschiedene Brennstoffeigenschaften sowohl in Simulationsstudien als auch durch Messdaten aus realen Biomassefeuerungen verifiziert. Die Ergebnisse dieser Verifikation zeigen, dass diese Methode in der Lage ist, die Brennstoffeigenschaften und Zustandsgrößen auch bei Last- oder Brennstoffwechseln genau zu bestimmen.

Um einen Betrieb der Biomassefeuerung mit möglichst hohem Wirkungsgrad und möglichst geringen Schadstoffemissionen zu gewährleisten, wird eine Methode zur CO-lambda-Optimierung entwickelt. Diese Methode verwendet einen erweiterten Kalman-Filter in Kombination mit Messdaten des Sauerstoffgehalts und des CO-Gehalts des Rauchgases zur Bestimmung eines optimalen Luftüberschussverhältnisses für den aktuellen Zustand der Biomassefeuerung. Diese Methode wird an einer realen Biomassefeuerung in einer Langzeitvalidierung über mehrere Monate verifiziert und validiert. Während dieser Langzeitvalidierung führte die Anwendung dieser Methode zur CO-lambda-Optimierung zu einer Wirkungsgradsteigerung von 3,8 %, einer Reduktion der CO-Emissionen um durchschnittlich 200 mg/m³ sowie einer Verringerung der Gesamtstaubemissionen um durchschnittlich 19 %.

Zusammenfassend ermöglicht die in dieser Arbeit vorgestellte modellbasierte Regelungsstrategie es, Biomassefeuerungen mit den geringstmöglichen Schadstoffemissionen und dem höchstmöglichen Wirkungsgrad zu betreiben und dabei ein hohes Maß an Brennstoffflexibilität und Lastmodulationsfähigkeit zu erreichen. Darüber hinaus weist die Regelungsstrategie eine geringe Komplexität auf und ist leicht in realen Biomassefeuerungen zu implementieren und zu warten. Dies ermöglicht den breiten Einsatz dieser Regelungsstrategie an bestehenden und zukünftigen Biomassefeuerungen. Dies unterstützt die weitere Verbreitung von Biomassefeuerungen im Energiesystem, was zur Reduzierung der CO2e-Emissionen beiträgt und auch die verstärkte Nutzung anderer, volatiler erneuerbarer Technologien, wie z.B. solarthermischer Anlagen, ermöglicht.

Peer reviewed papers | 2022

A multi-layer model of stratified thermal storage for MILP-based energy management systems

Muschick D, Zlabinger S, Moser A, Lichtenegger K, Gölles M. A multi-layer model of stratified thermal storage for MILP-based energy management systems. Applied Energy. 2022 May 15;315.118890. https://doi.org/10.1016/j.apenergy.2022.118890

External Link Details

Both the planning and operation of complex, multi-energy systems increasingly rely on optimization. This optimization requires the use of mathematical models of the system components. The model most often used to describe thermal storage, and especially in the common mixed-integer linear program (MILP) formulation, is a simple integrator model with a linear loss term. This simple model has multiple inherent drawbacks since it cannot be applied to represent the temperature distribution inside of the storage unit. In this article, we present a novel approach based on multiple layers of variable size but fixed temperature. The model is still linear, but can be used to describe the most relevant physical phenomena: heat losses, axial heat transport, and, at least qualitatively, axial heat conduction. As an additional benefit, this model makes it possible to clearly distinguish between heat available at different temperatures and thus suitable for different applications, e.g., space heating or domestic hot water. This comes at the cost of additional binary decision variables used to model the resulting hybrid linear dynamics, requiring the use of state-of-the-art MILP solvers to solve the resulting optimization problems. The advantages of the more detailed model are demonstrated by validating it against a standard model based on partial differential equations and by showing more realistic results for a simple energy optimization problem.

Other papers | 2022

Application of Optimization-based Energy Management Systems for Interconnected District Heating Networks

Kaisermayer V, Muschick D, Gölles M, Rosegger W, Binder J, Kelz J. Application of Optimization-based Energy Management Systems for Interconnected District Heating Networks. 22. Styrian Workshop on Automatic Control. 6 Sep. 2022. Leitring/Wagna, Österreich.

External Link Download PDF Details
Peer reviewed papers | 2022

Ash transformation during single-pellet gasification of sewage sludge and mixtures with agricultural residues with a focus on phosphorus

Hannl TK, Häggström G, Hedayati A, Skoglund N, Kuba M, Marcus Öhman. Ash transformation during single-pellet gasification of sewage sludge and mixtures with agricultural residues with a focus on phosphorus. Fuel Processing Technology. March 2022.227:107102.

External Link Details

The recovery of phosphorus (P) from sewage sludge ashes has been the focus of recent research due to the initiatives for the use of biogenic resources and resource recovery. This study investigates the ash transformation chemistry of P in sewage sludge ash during the co-gasification with the K-Si- and K-rich agricultural residues wheat straw and sunflower husks, respectively, at temperatures relevant for fluidized bed technology, namely 800 °C and 950 °C. The residual ash was analyzed by ICP­AES, SEM/EDS, and XRD, and the results were compared to results of thermochemical equilibrium calculations. More than 90% of P and K in the fuels were retained in the residual ash fraction, and significant interaction phenomena occurred between the P-rich sewage sludge and the K-rich ash fractions. Around 45–65% of P was incorporated in crystalline K-bearing phosphates, i.e., K-whitlockite and CaKPO4, in the residual ashes with 85–90 wt% agricultural residue in the fuel mixture. In residual ashes of sewage sludge and mixtures with 60–70 wt% agricultural residue, P was mainly found in Ca(Mg,Fe)-whitlockites and AlPO4. Up to about 40% of P was in amorphous or unidentified phases. The results show that gasification provides a potential for the formation of K-bearing phosphates similar to combustion processes.

Peer reviewed papers | 2022

Assessment of measurement methods to characterize the producer gas from biomass gasification with steam in a fluidized bed

Anca-Couce A, von Berg L, Pongratz G, Scharler R, Hochenauer C, Geusebroek M, Kuipers J, Vilela CM, Kraia T, Panopoulos K, Funcia I, Dieguez-Alonso A, Almuina-Villar H, Tsiotsias T, Kienzl N, Martini S. Assessment of measurement methods to characterize the producer gas from biomass gasification with steam in a fluidized bed. Biomass and Bioenergy 2022.163:106527

External Link Details

Measuring the producer gas from biomass gasification is very challenging and the use of several methods is required to achieve a complete characterization. Various techniques are available for these measurements, offering very different affordability or time demand requirements and the reliability of these techniques is often unknown. In this work an assessment of commonly employed measuring methods is conducted with a round robin. The main permanent gases, light hydrocarbons, tars, sulfur and nitrogen compounds were measured by several partners employing a producer gas obtained from fluidized bed gasification of wood and miscanthus with steam. Online and offline methods were used for this purpose and their accuracy, repeatability and reproducibility are here discussed. The results demonstrate the reliability of gas chromatography for measuring the main permanent gases, light hydrocarbons, benzene and H2S, validating the obtained results with other methods. An online method could also measure NH3 with a reasonable accuracy, but deviations were present for compounds at even lower concentrations. Regarding tar sampling and analysis, the main source of variability in the results was the analysis of the liquid samples, especially for heavier compounds. The presented work pointed out the need for a complementary use of several techniques to achieve a complete characterization of the producer gas from biomass gasification, and the suitability of certain online techniques as well as their limitations.

Conference presentations and posters | 2022

Automatic Thermal Model Identification and Distributed Optimisation for Load Shifting in City Quarters

Moser A, Kaisermayer V, Muschick D, Zemann C, Gölles M, Hofer A, Brandl D, Heimrath R, Mach T, Tugores C R, Ramschak, T. Automatic Thermal Model Identification and Distributed Optimisation for Load Shifting in City Quarters. 2nd International Sustainable Energy Conference: ISEC 2022. Graz, 07/04/2022. Oral presentation.

Download PDF Details

Modern buildings with floor heating or thermally activated building structures (TABS) offer a significant potential for shifting the thermal load and thus reduce peak demand for heating or cooling. This potential can be realized with the help of model predictive control (MPC) methods, provided that sufficiently descriptive mathematical models describing the thermal characteristics of the individual thermal zones exist. Creating these by hand or from more detailed simulation models is infeasible for large numbers of zones; instead, they must be identified automatically based on measurement data. We present an approach using only open source tools based on the programming language Julia that allows to robustly identify simple thermal models for heating and cooling usable in MPC optimization. The resulting models are used in a distributed optimization scheme that co-ordinates the individual zones and buildings of a city quarter in order to best support an energy hub.

Other papers | 2022

Automatic thermal model identification and distributed optimization for load shifting in city quarters

Moser AGC, Kaisermayer V, Muschick D, Gölles M, Hofer A, Brandl D, Heimrath R, Mach T, Ribas Tugores C, Ramschak T. Automatic thermal model identification and distributed optimization for load shifting in city quarters. in Conference Proceedings - 2nd International Sustainable Energy Conference. 2022. S. 302-303 https://doi.org/10.32638/isec2022

External Link Details

Modern buildings with floor heating or thermally activated building structures (TABS) offer a significant
potential for shifting the thermal load and thus reduce peak demand for heating or cooling. This potential can be realized with the help of model predictive control (MPC) methods, provided that sufficiently descriptive mathematical models describing the thermal characteristics of the individual thermal zones exist. Creating these by hand or from more detailed simulation models is infeasible for large numbers of zones; instead, they must be identified automatically based on measurement data. We present an approach using only open source tools based on the programming language Julia that allows to robustly identify simple thermal models for heating and cooling usable in MPC optimization. The resulting models are used in a distributed optimization scheme that co-ordinates the individual zones and buildings of a city quarter in order to best support an energy hub.

Other Publications | 2022

ÖKO-OPT-AKTIV: Optimiertes Regelungs- und Betriebsverhalten thermisch aktivierter Gebäude zukünftiger Stadtquartiere

Abschlussworkshop

Muschick D, Kaisermayer V. ÖKO-OPT-AKTIV - Optimiertes Regelungs- und Betriebsverhalten thermisch aktivierter Gebäude zukünftiger Stadtquartiere. Präsentation beim Abschlussworkshop in Graz, 16.09.2022.

Download PDF Details
Conference presentations and posters | 2022

BEST-Day

Sustainable biorefineries and digitalization

Schwabl M, Wopienka E, Drosg B, Kuba M, Weber G, Eßl M, Gölles M, Kaiermayer V, Liedte P, Fuhrmann M. BEST-Day: Sustainable biorefineries and digitalization. 7th Central European Biomass Conference CEBC 2023. 18. January 2023. Graz. Oral Presentation.

Download PDF Details

List of presentations:

Biorefineries

  • Learnings from biomass combustion towards future bioenergy applications (M. Schwabl)
  • Green Carbon perspectives for regional sourcing and decarbonization (E. Wopienka)
  • Bioconversion processes for renewable energy and/or biological carbon capture and utilisation (B. Drosg)
  • Second generation biomass gasification: The Syngas Platform Vienna – current status and outlook (M. Kuba)
  • Utilization of syngas for the production of fuel and chemicals – recent developments and outlook (G. Weber)

Digital methods, tools and sustainability

  • Evaluation of different numerical models for the prediction of NOx emissions of small-scale biomass boilers (M. Eßl)
  • Digitalization as the basis for the efficient and flexible operation of renewable energy technologies (M. Gölles)
  • Smart Control for Coupled District Heating Networks (V. Kaisermayer)
  • Integrated energy solutions for a decentral energy future - challenges and solutions (P. Liedtke)
  • Wood-Value-Tool: Techno-economic assessment of the forest-based sector in Austria (M. Fuhrmann)
Other Publications | 2022

CleanAir2 project – citizen science investigating real-life emission from firewood stove

Schwabl M. CleanAir2 project – citizen science investigating real-life emission from firewood stove. Workshop 2: Advances in Instrumentation Used for Wood Heater Testing and Field Data Collection. March 2022.

Details
Conference presentations and posters | 2022

Conference contribution - Energy and Climate Transformations 3rd International Conference on Energy Research & Social Science

Download PDF Details

A better understanding of the underlying motives of consumers considering a new RESS (heating,
cooling and electricity) can contribute to create favorable conditions for an energy transition.
Therefore, the main objectives of this research project are to:
▪ Identify motives of consumers interested in ordeciding for a certain RESS
▪ Assess the impact of gender and intersectingaspects, such as age, income and education on these motives.

Other Publications | 2022

Einsatz von Aschen aus Biomassefeuerungen in der Forst- und Landwirtschaft

Retschitzegger S. Einsatz von Aschen aus Biomassefeuerungen in der Forst- und Landwirtschaft. Seminar - Effizienter Heizwerkbetrieb. March 2022

Details
Other Publications | 2022

Energiegemeinschaften im Tourismussektor

External Link Details

Der Leitfaden „Energiegemeinschaften im Tourismus“ zeigt, welche Möglichkeiten Energiegemeinschaften für Tourismusbetriebe, ihre Beschäftigten und Menschen, die in Tourismusregionen leben, bieten können und wie eine Energiegemeinschaft ins Leben gerufen werden
kann.

Peer reviewed papers | 2022

Expert survey and classification of tools for modeling and simulating hybrid energy networks

Widl E, Cronbach D, Sorknæs P, Fitó J, Muschick D, Repetto M, Ramousse J, Ianakiev A. Expert survey and classification of tools for modeling and simulating hybrid energy networks. Sustainable Energy, Grids and Networks. December 2022.32:100913.

External Link Details

Sector coupling is expected to play a key role in the decarbonization of the energy system by enabling the integration of decentralized renewable energy sources and unlocking hitherto unused synergies between generation, storage and consumption. Within this context, a transition towards hybrid energy networks (HENs), which couple power, heating/cooling and gas grids, is a necessary requirement to implement sector coupling on a large scale. However, this transition poses practical challenges, because the traditional domain-specific approaches struggle to cover all aspects of HENs. Methods and tools for conceptualization, system planning and design as well as system operation support exist for all involved domains, but their adaption or extension beyond the domain they were originally intended for is still a matter of research and development. Therefore, this work presents innovative tools for modeling and simulating HENs. A categorization of these tools is performed based on a clustering of their most relevant features. It is shown that this categorization has a strong correlation with the results of an independently carried out expert review of potential application areas. This good agreement is a strong indicator that the proposed classification categories can successfully capture and characterize the most important features of tools for HENs. Furthermore, it allows to provide a guideline for early adopters to understand which tools and methods best fit the requirements of their specific applications.

Conference presentations and posters | 2022

FAULT DETECTIVE: FAULT DETECTION FOR SOLAR THERMAL SYSTEMS

Feierl L, Bolognesi T, Unterberger V, Geatani M, Gerardts B. FAULT DETECTIVE: FAULT DETECTION FOR SOLAR THERMAL SYSTEMS. ISEC 2022. 05 - 07. April 2022, Graz. Poster presentation.

Details
Peer reviewed papers | 2022

Glycogen, poly(3-hydroxybutyrate) and pigment accumulation in three Synechocystis strains when exposed to a stepwise increasing salt stress

Meixner K, Daffert C, Dalnodar D, Mrázová K, Hrubanová K, Krzyzanek V, Nebesarova J, Samek O, Šedrlová Z, Slaninova E, Sedláček P, Obruča S, Fritz I. Glycogen, poly(3-hydroxybutyrate) and pigment accumulation in three Synechocystis strains when exposed to a stepwise increasing salt stress. Journal of Applied Phycology. June 2022. 34 (3):1227 - 1241.

External Link Details

The cyanobacterial genus Synechocystis is of particular interest to science and industry because of its efficient phototrophic metabolism, its accumulation of the polymer poly(3-hydroxybutyrate) (PHB) and its ability to withstand or adapt to adverse growing conditions. One such condition is the increased salinity that can be caused by recycled or brackish water used in cultivation. While overall reduced growth is expected in response to salt stress, other metabolic responses relevant to the efficiency of phototrophic production of biomass or PHB (or both) have been experimentally observed in three Synechocystis strains at stepwise increasing salt concentrations. In response to recent reports on metabolic strategies to increase stress tolerance of heterotrophic and phototrophic bacteria, we focused particularly on the stress-induced response of Synechocystis strains in terms of PHB, glycogen and photoactive pigment dynamics. Of the three strains studied, the strain Synechocystis cf. salina CCALA192 proved to be the most tolerant to salt stress. In addition, this strain showed the highest PHB accumulation. All the three strains accumulated more PHB with increasing salinity, to the point where their photosystems were strongly inhibited and they could no longer produce enough energy to synthesize more PHB.

Other Publications | 2022

Grundlagenforschung Smart- und Microgrids / Endbericht

Innovative, selbstlernende Systemregler für dezentrale Energieressourcen & Microgrids

Michael Zellinger, Michael Stadler

Download PDF Details

Mikro-Netze (Microgrids), ein Unterbereich der Intelligenten Strom/Energie-Netze (Smartgrids),
die sich durch eine enge räumliche Bindung von Energieerzeugungseinheiten und Verbraucher
auszeichnen wird international ein sehr starkes Wachstum zugeschrieben. Microgrids sind kleine,
lokale Energienetze für Strom, Wärme und Kälte, die Haushalte, Betriebe und Gemeinden mit
Energie versorgen. Diese lokalen und regionalen Konzepte der Energieversorgung können in
Zukunft einen wesentlichen Beitrag in Richtung Energieunabhängigkeit und effizientere
Integration von Erneuerbaren in das Energiesystem leisten. Sie können ihren Energiebedarf
selbstständig aus erneuerbaren Energien oder anderen Energieformen decken, etwa Biomasse,
Wärmepumpen, PV, Windräder oder Kraftwärmekopplungen. Diese können nach den
individuellen Zielen der Gemeinden, Haushalte oder der Betriebe gesteuert werden, um
Kostenreduktionen, CO2 Einsparungen oder eine Erhöhung des Unabhängigkeitsgrades zu
realisieren. Sie berechnen den aktuellen und zukünftigen Verbrauch und können Energie im
Bedarfsfall dorthin verlagern, wo sie gerade benötigt wird, oder sie reduzieren den
Energieverbrauch direkt.

Reports | 2022

IEA Bioenergy Task 44: Flexible Bioenergie und Systemintegration (Arbeitsperiode 2019 - 2021)

Gölles M, Schipfer F. IEA Bioenergy Task 44: Flexible Bioenergie und Systemintegration (Arbeitsperiode 2019 - 2021). IEA Task Bioenergy 44. BMK. Schriftenreihe 49/2023. Deutsch, 40 Seiten.

External Link Details

Ziel des Tasks ist es, Bioenergielösungen als flexible Ressource in einem dekarbonisierten Energiesystem herauszuarbeiten. Dabei sollen Typen, Qualität und Status von flexibler Bioenergie erhoben sowie Barrieren und Entwicklungsbedarf im Gesamtsystemkontext (Strom-, Wärme- und Transportsektor) identifiziert werden.

Conference presentations and posters | 2022

IEA SHC Task 68: Efficient Solar District Heating Systems

Unterberger V, Berberich M, Putz S, Byström J, Gölles M. IEA SHC Task 68: Efficient Solar District Heating Systems. ISEC 2022. 5 - 07. April 2022, Graz. Poster presentation.

Download PDF Details
Peer reviewed papers | 2022

Increased Flexibility of A Fixed-Bed Biomass Gasifier through Advanced Control

Hollenstein C, Zemann C, Martini S, Gölles M, Felsberger W, Horn M. Increased Flexibility of A Fixed-Bed Biomass Gasifier through Advanced Control. Proceedings of the 30th European Biomass Conference and Exhibition. 2022. 704-711.

External Link Details

Most industrial fixed-bed biomass gasification systems usually operate at steady-state to produce the maximum amount of energy possible although they can principally modulate their loads to compensate for the fluctuations of other volatile renewable energy systems. To unleash their full load modulation capability, their typically traditional control strategies should be improved, their gas residence times affected by typically basic char removal strategies adjusted and any required manual interaction of an operator avoided. In this respect, a new controller for the char handling (accumulation and removal) of the reduction zone in a fixed-bed biomass gasifier of a representative industrial small-scale gasification system is developed and experimentally verified. This new controller consists of a recursive least-squares estimator for the flow resistance of the gasifier representing the amount of char inside and a switching controller for rotating a grate located at its bottom. The experimental verification reveals that only the traditional (pressure-based) controller requires manual adjustment of the thresholds. Moreover, the new controller (flow resistance based) significantly reduces the fluctuation range during partial load and stabilizes the temperature and pressure downstream the gasifier. This provides the basis for enhancing its fuel flexibility too and is an important feature for flexible operation in future.

Peer reviewed papers | 2022

Influence of bed materials on the performance of the Nong Bua dual fluidized bed gasification power plant in Thailand

Siriwongrungson V, Hongrapipat J, Kuba M, Rauch R, Pang S, Thaveesri J, Messner M, Hofbauer H. Influence of bed materials on the performance of the Nong Bua dual fluidized bed gasification power plant in Thailand. Biomass Conversion and Biorefinery 2022. 12:2965-2979.

External Link Details

Bed materials and their catalytic activity are two main parameters that affect the performance of the dual fluidized bed (DFB) gasification system in terms of product gas composition and tar levels. Two sources of bed materials were used for the operation of a commercial DFB gasification system in Thailand, using woodchips as a biomass feedstock. One source of the bed materials was the calcined olivine which had been used in the Gussing Plant, Austria, and the other activated bed material was a mixture of fresh Chinese olivine and used Austrian olivine with additives of biomass ash, calcium hydroxide and dolomite. These bed materials were collected and analysed for morphological and chemical composition using a scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray fluorescence spectroscopy (XRF). The product gas was cleaned in a scrubber to remove tars, from which the samples were collected for gravimetric tar analysis. Its composition data was automatically recorded at the operation site before it entered the gas engine. From the SEM, EDS and XRF analyses, calcium-rich layers around the bed materials were observed on the activated bed material. The inner layers of bed materials collected were homogeneous. Biomass ash, which was generally added to the bed materials, had significant calcium and potassium content. These calcium-rich layers of the bed materials, from the calcium hydroxide, biomass ash and dolomite, influenced system performance, which was determined by observing lower tar concentration and higher hydrogen concentration in the product gas.

Conference presentations and posters | 2022

Integration of biomass gasification into the forest based sector in Austria

Fuhrmann M, Dißauer Ch, Strasser Ch, Schmid E. Integration of biomass gasification into the forest based sector in Austria. 21 September 2022. ISIE SEM Conference, Vienna

Download PDF Details
Other Publications | 2022

Key Messages – Kurze Zusammenfassung der Ergebnisse aus der Motivanalyse

Download PDF Details

„Welche Heizung passt zu mir/uns? Vielleicht auch Kühlen oder selber Strom erzeugen?“ – Diese
Fragen stellen sich oft, wenn der Traum von den eigenen vier Wänden näher rückt. Egal ob bei Neubau
oder Sanierung, die Wahl eines passenden Energiebereitstellungssystems (EBS) sollte wohl überlegt
sein. Neben den technologischen Fragen sind es auch persönliche Motive, welche die Entscheidung
der Nutzer*innen beeinflussen.

Conference presentations and posters | 2022

MATHEMATICAL MODEL FOR MODEL-BASED CONTROL OF ABSORPTION HEAT PUMPING SYSTEMS

Zlabinger S, Unterberger V, Gölles M, Horn M, Wernhart M, Rieberer R. MATHEMATICAL MODEL FOR MODEL-BASED CONTROL OF ABSORPTION HEAT PUMPING SYSTEMS. 2nd International Sustainable Energy Conference – ISEC 2022. October 2022.

Details
Reports | 2022

Minimization of inorganic particulate matter emissions with a novel multi-fuel combustion technology that enhances inorganic retention in a compact updraft fixed-bed

Archan GAR, Scharler R, Buchmayr M, Kienzl N, Hochenauer C, Gruber J, Anca-Couce A. Minimization of inorganic particulate matter emissions with a novel multi-fuel combustion technology that enhances inorganic retention in a compact updraft fixed-bed. Fuel. 2022.318:123611

External Link Details

A novel biomass combustion technology was investigated that operates at a low oxygen content under fixed-bed and double air staging conditions. This technology was used to achieve extremely low NOX and particle matter emissions in a 30 kW lab-scale reactor, displaying high fuel flexibility and no slagging. In this experimental work, the aim was to minimize inorganic particulate matter emissions, this aim was achieved by enabling the very low release of inorganics such as K from the fixed bed, which operates like a compact updraft gasifier. The elemental composition of the employed fuels, emitted dust particles, and fuel particle samples taken at three different heights within the fixed bed, and the bed temperatures were measured. The main objective in this study was to determine and understand the different processes of inorganic matter release that take place within the compact fixed bed. The results show that 98% and 99.7% of the K could be retained in the fixed bed for wood chips and miscanthus pellets, respectively, thus minimizing the particulate matter emissions. Different processes in the context of K release within the fixed bed could be identified for silica rich/agricultural and calcium rich / woody fuels, respectively and inconsistencies in the literature on these mechanisms could be resolved. In the case of miscanthus pellets, K is retained in silicates, and no accumulation of K, Cl and S occurs in the fixed bed above. In the case of wood chips, on the other hand, there is an unexpected K accumulation in the fixed bed, which is due to the release of K in the hot oxidation zone and the subsequent formation of large amounts of K chlorides and sulfates by condensation in the cooler upper region. Furthermore, for woody fuels, bounding or intercalation of K into the char matrix plays a more important role than the formation of carbonates in avoiding K release from the bed.

Conference presentations and posters | 2022

Model-based control of absorption heat pumping systems

Staudt S, Unterberger V, Muschick D, Wernhart M, Rieberer R. Model-based control of absorption heat pumping systems. 2022. Abstract from 22. Styrian Workshop on Automatic Control, Leitring/Wagna, Austria.

External Link Details

Absorption heat pumping systems (AHPSs, comprising absorption heat pumps and chillers) are devices that mainly use thermal energy instead of electricity to generate heating and cooling. This thermal energy can be provided by, e.g., waste heat or renewable energy sources such as solar energy, which allow AHPSs to contribute to ressource-efficient heating and cooling systems. Despite this benefit, AHPSs are still not a widespread technology. One reason for this is unsatisfactory controllability under varying operating conditions, which results in poor modulation and partial load capability. Emloying model-based control is a promising approach to address this issue, which will be the focus of this  contribution.
First, a viable control-oriented model for AHPSs is developed. It is based on physical correlations to facilitate systematic adaptions to different scales and operating conditions and considers only the most relevant mass and energy stores to keep the model order at a minimum. The resulting model is mathematically simple but still has the structure of a nonlinear differential-algebraic system of equations. This is typical for models of thermo-chemical
processes, but is unfortunately not suitable for many control design methods. Therefore, linearization at an operating point is discussed to derive a model in linear state space representation. Experimental validation results show that the linearized model does have slightly worse steady-state accuracy than the nonlinear model, but that the dynamic accuracy seems to be almost unaffected by the linearization and is considered sufficiently good to be used in control design.
As a next step, the linearized model is used to design model-based control strategies for AHPSs. A special focus is put on redundantly-actuated configurations, i.e. configurations with more manipulated variables than controlled variables, which allows using additional degrees of freedom to extend the operating range of AHPS and hence improve their partial load capability. Two model-based control approaches are discussed: First, a linear model predictive control (MPC) approach is presented - a well-established and generally easy-to-parameterize approach, which, however, often results in high computational effort prohibitive to its implementation on a conventional PLC. Therefore, a second control approach based on state feedback is presented which is mathematically simple enough for implementation on a conventional PLC. It consists of an observer for state variables and unknown disturbances, a state feedback controller and, in case of redundantly-actuated configurations, a dynamic control allocation algorithm. Both approaches are experimentally validated and compared to a state-of-the art control approach based on SISO PI control, showing that the model-based MIMO control approaches allow for a wider operating range and hence better modulation and partial load capability compared to the SISO PI approach. This, in turn, reduces ON/OFF operation of AHPSs and also facilitates their integration into complex energy systems to generate heating and cooling in a ressource-efficient manner.

Peer reviewed papers | 2022

Multi-scale modelling of fluidized bed biomass gasification using a 1D particle model coupled to CFD

von Berg L, Anca-Couce A, Hochenauer C, Scharler R. Multi-scale modelling of fluidized bed biomass gasification using a 1D particle model coupled to CFD. Fuel. 15 September 2022.324:124677

External Link Details

For many fluidized bed applications, the particle movement inside the reactor is accompanied by reactions at the particle scale. The current study presents for the first time in literature a multi-scale modelling approach coupling a one-dimensional volumetric particle model with the dense discrete phase model (DDPM) of ANSYS Fluent via user defined functions. To validate the developed modelling approach, the current study uses experimental data of pressure drop, temperature and gas composition obtained with a lab-scale bubbling fluidized bed biomass gasifier. Therefore, a particle model developed previously for pyrolysis was modified implementing a heat transfer model valid for fluidized bed conditions as well as kinetics for char gasification taken from literature. The kinetic theory of granular flow is used to describe particle–particle interactions allowing for feasible calculation times at the reactor level whereas an optimized solver is employed to guarantee a fast solution at the particle level. A newly developed initialization routine uses an initial bed of reacting particles at different states of conversion calculated previously with a standalone version of the particle model. This allows to start the simulation at conditions very close to stable operation of the reactor. A coupled multi-scale simulation of over 30 s of process time employing 300.000 inert bed parcels and about 25.000 reacting fuel parcels showed good agreement with experimental data at a feasible calculation time. Furthermore, the developed approach allows for an in-depth analysis of the processes inside the reactor allowing to track individual reacting particles while resolving gradients inside the particle.

Other papers | 2022

Netzdienliche Nutzung von Bauteilaktivierung in Gebäuden durch vorausschauende Regelungen – Ergebnisse aus dem Projekt ÖKO-OPT-AKTIV

Kaisermayer V, Muschick D, Gölles M. Netzdienliche Nutzung von Bauteilaktivierung in Gebäuden durch vorausschauende Regelungen – Ergebnisse aus dem Projekt ÖKO-OPT-AKTIV. Abschlussworkshop - IEA DHC Annex TS3: Hybride Energie-Netze. 20. Oktober 2022, online.

Download PDF Details
Reports | 2022

Optimiertes Regelungs- und Betriebsverhalten thermisch aktivierter Gebäude zukünftiger Stadtquartiere (ÖKO-OPT-AKTIV)

Muschick D, Kaisermayer V, Moser A, Gölles M, Heimrath R, Brandl D, Mach T, Ribas-Tugores C, Ramschak T, Oswald S, Polster M, Lackner F, Eibisberger K, Nebel M. Optimiertes Regelungs- und Betriebsverhalten thermisch aktivierter Gebäude zukünftiger Stadtquartiere (ÖKO-OPT-AKTIV). Stadt der Zukunft 6. Ausschreibung. BMK. Schriftenreihe 60/2023. Jänner, 2022. Deutsch, 76 Seiten.

External Link Details
Reports | 2022

PHB Producing Cyanobacteria Found in the Neighborhood— Their Isolation, Purification and Performance Testing

Meixner K, Daffert C, Bauer L, Drosg B, Fritz I. PHB Producing Cyanobacteria Found in the Neighborhood— Their Isolation, Purification and Performance Testing. 2022.9:178

External Link Details

Cyanobacteria are a large group of prokaryotic microalgae that are able to grow photo-autotrophically by utilizing sunlight and by assimilating carbon dioxide to build new biomass. One of the most interesting among many cyanobacteria cell components is the storage biopolymer polyhydroxybutyrate (PHB), a member of the group of polyhydroxyalkanoates (PHA). Cyanobacteria occur in almost all habitats, ranging from freshwater to saltwater, freely drifting or adhered to solid surfaces or growing in the porewater of soil, they appear in meltwater of glaciers as well as in hot springs and can handle even high salinities and nutrient imbalances. The broad range of habitat conditions makes them interesting for biotechnological production in facilities located in such climate zones with the expectation of using the best adapted organisms in low-tech bioreactors instead of using “universal” strains, which require high technical effort to adapt the production conditions to the organism‘s need. These were the prerequisites for why and how we searched for locally adapted cyanobacteria in different habitats. Our manuscript provides insight to the sites we sampled, how we isolated and enriched, identified (morphology, 16S rDNA), tested (growth, PHB accumulation) and purified (physical and biochemical purification methods) promising PHB-producing cyanobacteria that can be used as robust production strains. Finally, we provide a guideline about how we managed to find potential production strains and prepared others for basic metabolism studies.

Peer reviewed papers | 2022

Real coupling of solid oxide fuel cells with a biomass steam gasifier: Operating boundaries considering performance, tar and carbon deposition analyses

Pongratz G, Subotić V, von Berg L, Schroettner H, Hochenauer C, Martini S, Hauck M, Steinruecken B, Skrzypkiewicz M, Kupecki J, Scharler R, Anca-Couce A. Real coupling of solid oxide fuel cells with a biomass steam gasifier: Operating boundaries considering performance, tar and carbon deposition analyses. Fuel. 15 May 2022.316:123310.

External Link Details

Solid oxide fuel cells are a promising alternative to gas engines for combined heat and power production based on biomass gasification. The technical complexity of realizing gasifier – fuel cell couplings has limited the number of experiments conducted in the past. However, results from such experiments are of high importance for the evaluation of tar thresholds and operating conditions ensuring a stable operation of fuel cells. For the first time, it was possible to demonstrate for dozens of hours the operation of solid oxide fuel cells with real product gas from steam gasification with a steam-to-carbon ratio of 2 and a typical tar content for fluidized bed gasification. Four coupling experiments with industrial-relevant cell designs were conducted, demonstrating a stable operation for 30 h without structural degradation of the anodes for cells with nickel/ceria- and nickel/zirconia-based anodes at 800°C and 850°C, if heavy tars were partially removed (2.8–3.7 g·Nm−3 gravimetric tars). Raw gas operation (4.6–4.8 g·Nm−3 gravimetric tars) led to metal dusting effects on nickel contact meshes and nickel/zirconia-based anodes, whereas nickel/ceria-based anodes were less affected. Carbon deposited on the alumina support in all experiments whereby a change from pyrolytic to graphitic structure could be observed when increasing the temperature from 800°C to 850°C, thus significantly reducing the risk for blockages in the flow channels. Moreover, high tar and benzene conversion rates were observed. Concluding, operating temperatures of 850°C and the removal only of heavy tars can enable stable long-term operation with a tar-laden steam gasifier product gas, even without increasing the steam-to-carbon ratio to values exceeding two.

Peer reviewed papers | 2022

Self-Heating of Biochar during Postproduction Storage by O2 Chemisorption at Low Temperatures

Phounglamcheik A, Johnson N, Kienzl N, Strasser C, Umeki K. Self-Heating of Biochar during Postproduction Storage by O2 Chemisorption at Low Temperatures. Energies. 2022.15:380

External Link Details

Biochar is attracting attention as an alternative carbon/fuel source to coal in the process industry and energy sector. However, it is prone to self-heating and often leads to spontaneous ignition and thermal runaway during storage, resulting in production loss and health risks. This study investigates biochar self-heating upon its contact with O2 at low temperatures, i.e., 50–300 °C. First, kinetic parameters of O2 adsorption and CO2 release were measured in a thermogravimetric analyzer using biochar produced from a pilot-scale pyrolysis process. Then, specific heat capacity and heat of reactions were measured in a differential scanning calorimeter. Finally, a one-dimensional transient model was developed to simulate self-heating in containers and gain insight into the influences of major parameters. The model showed a good agreement with experimental measurement in a closed metal container. It was observed that char temperature slowly increased from the initial temperature due to heat released during O2 adsorption. Thermal runaway, i.e., self-ignition, was observed in some cases even at the initial biochar temperature of ca. 200 °C. However, if O2 is not permeable through the container materials, the temperature starts decreasing after the consumption of O2 in the container. The simulation model was also applied to examine important factors related to self-heating. The results suggested that self-heating can be somewhat mitigated by decreasing the void fraction, reducing storage volume, and lowering the initial char temperature. This study demonstrated a robust way to estimate the cooling demands required in the biochar production process.

Peer reviewed papers | 2022

Smart control of interconnected district heating networks on the example of “100% Renewable District Heating Leibnitz”

Kaisermayer V, Binder J, Muschick D, Beck G, Rosegger W, Horn M, Gölles M, Kelz J, Leusbrock I. Smart control of interconnected district heating networks on the example of “100% Renewable District Heating Leibnitz”. Smart Energy. 2022 Apr 7. 100069. https://doi.org/10.1016/j.segy.2022.100069

External Link Details

District heating (DH) networks have the potential for intelligent integration and combination of renewable energy sources, waste heat, thermal energy storage, heat consumers, and coupling with other sectors. As cities and municipalities grow, so do the corresponding networks. This growth of district heating networks introduces the possibility of interconnecting them with neighbouring networks. Interconnecting formerly separated DH networks can result in many advantages concerning flexibility, overall efficiency, the share of renewable sources, and security of supply. Apart from the problem of hydraulically connecting the networks, the main challenge of interconnected DH systems is the coordination of multiple feed-in points. It can be faced with control concepts for the overall DH system which define optimal operation strategies. This paper presents two control approaches for interconnected DH networks that optimize the supply as well as the demand side to reduce CO2 emissions. On the supply side, an optimization-based energy management system defines operation strategies based on demand forecasts. On the demand side, the operation of consumer substations is influenced in favour of the supply using demand side management. The proposed approaches were tested both in simulation and in a real implementation on the DH network of Leibnitz, Austria. First results show a promising reduction of CO2 emissions by 35% and a fuel cost reduction of 7% due to better utilization of the production capacities of the overall DH system.

Other Publications | 2022

Solar goes Digital: Wie Solarwärme selbstlernende Algorithmen nutzt (Austria Solar Webinar 26)

Unterberger V. Solar goes Digital: Wie Solarwärme selbstlernende Algorithmen nutzt (Austria Solar Webinar 26). Online am 11.05.2022.

External Link Download PDF Details
Peer reviewed papers | 2022

Solid oxide fuel cell operation with biomass gasification product gases: Performance- and carbon deposition risk evaluation via a CFD modelling approach

Pongratz G, Subotić V, Hochenauer C, Scharler R, Anca-Couce A. Solid oxide fuel cell operation with biomass gasification product gases: Performance- and carbon deposition risk evaluation via a CFD modelling approach. 1 April 2022. 244.

External Link Details

Solid oxide fuel cell (SOFC) models used in the past for biomass-to-power plant simulations are limited in their predictability of the carbon deposition risk. In this work, industrial-relevant cell designs were modeled in 2D-CFD considering detailed reaction kinetics which allowed more accurate performance simulations and carbon deposition risk assessments. Via a parametric study, the influence of varying cell operating conditions on the cell performance and carbon deposition risk was quantified when utilizing product gases from steam- and air gasification with varying steam addition. Considering the results from this parameter study and carbon deposition risk assessment, recommendations for promising gasifier-SOFC configurations and cell operating points for stable long-term operation are presented. For smaller-scale biomass-to-power systems, the utilization of product gas from air gasification in anode supported cells with Ni/zirconia-based anode can be recommended, with only moderate steam dilution of the product gas at 750°C cell operating temperature. For larger scales, steam gasification might be meaningful, offering a generally higher electrical efficiency and power output in fuel cells than air gasification. However, a higher risk for carbon deposition could be determined in comparison to air gasification. Hence, a cell temperature of 850°C besides the use of cells with Ni/ceria-based anodes is recommended.

Conference presentations and posters | 2022

Success Factors and Barriers for Integrated District Heating Networks

Muschick D, Cronbach D, Ianakiev A, Kallert A, Schmidt R-R, Sorknaes P et al. Success Factors and Barriers for Integrated District Heating Networks. 2022. Postersitzung präsentiert bei 2nd International Sustainable Energy Conference , Graz, Österreich.

Details
Other Publications | 2022

Techno-economic assessment of wood-based processes with feedstock price scenarios in Austria

Fuhrmann M, Dißauer Ch, Strasser Ch, Schmid E. Techno-economic assessment of wood-based processes with feedstock price scenarios in Austria. Austrian Journal of Agricultural Economics and Rural Studies.31.15

Download PDF Details

Woody biomass is a raw material and cost factor for a range of industries in Austria. The aim of this article is to assess impacts of price developments on operating costs of particleboard, combined heat and power (CHP) and synthetic natural gas (BioSNG) production. Three price scenarios have been developed for pulpwood, industrial wood chips and forest wood chips for the period 2021 - 2026. Results show that the share of raw material costs on total operating costs ranges between 24 - 64% for particleboard, 45 - 82% for CHP, and 24 - 63% for BioSNG production.

Other papers | 2022

Technology and Process Improvement of a Demonstration Unit for a Novel Aqueous Phase Reforming Process Via Virtual Commissioning

Nigitz T, Arlt S, Poms U, Weber G, Luisser M, Gölles M. Technology and Process Improvement of a Demonstration Unit for a Novel Aqueous Phase Reforming Process Via Virtual Commissioning. Proceedings of the 30th European Biomass Conference and Exhibition. 2022. 948 - 950.

External Link Details

A process demonstration unit for a novel aqueous phase reforming (APR) process was built and scaled up by factor 666. The set-up of this demonstration unit was supported by virtual commissioning using a virtual test bed. By using virtual commissioning, it was possible to speed-up the commissioning and to support stable, reliable and continuous plant operation for 100h.

Peer reviewed papers | 2022

The effect of the presence of water on sulfur removal capacity during H2S removal from syngas using ZnO adsorbent

Dogan C, Martini S, Rets hitzegger S, Cetin B. The effect of the presence of water on sulfur removal capacity during H2S removal from syngas using ZnO adsorbent. Environmental Technology. 15 May 2022.

External Link Details

Compared to extensive studies on affecting parameters in sulfur removal with ZnO adsorbents from coal gasification syngas, similar studies conducted for biomass gasification syngas (BGS) are quite rare. Thus, considering the BGSs with high water content, this study was performed to investigate the effect of H2O presence in syngas on sulfur removal capacity (SRC) of ZnO adsorbents. Initially, the effect of gas composition and temperature on SRC in binary gas mixture was investigated. While H2O decreased the SRC, as expected, the highest reduction in the capacity occurred in the CO–H2S gas mixture due to observed COS formation. Second, the SRCs and resulting COS formation were compared for synthetic syngas mixtures having different water contents and for different amounts of adsorbents. Finally, the separate and combined effects of temperature and H2O on SRC and COS formation in synthetic syngas were investigated by comparing SRCs of typical syngas under wet and dry conditions. The results showed that increasing the amount of adsorbent and temperature results in higher SRC due to a reduction in COS formation through the reactions of COS with H2 and H2O. This indicates that it is critical to control the residence time of syngas and temperature to reduce COS formation during ZnO adsorption.

Peer reviewed papers | 2022

Thermodynamic Equilibrium Study on the Melting Tendency of the K-Ca-Mg-P-Si-O System with Relevance to Woody and Agricultural Biomass Ash Compositions

Falk J, Hannl TK, Skoglund N, Backman R, Öhman M. Thermodynamic Equilibrium Study on the Melting Tendency of the K-Ca-Mg-P-Si-O System with Relevance to Woody and Agricultural Biomass Ash Compositions. Energy and Fuels 7 July 2022.36(13):7035-7051.

External Link Details

A major challenge in the combustion of biomass fuels is the heterogeneity of ash-forming elements, which may cause a wide range of ash-related problems. Understanding the melting tendency of the coarse ash fractions is necessary to mitigate agglomeration and slagging. This work aims to evaluate the melting tendency of the K-Ca-Mg-Si-P-O system by use of thermodynamic equilibrium calculations. The formation of condensed phases were systematically assessed in a combustion atmosphere, varying temperatures, and composition. Compositional ranges were based on fuel ash data extracted from the Phyllis 2 database. The speciation and degree of polymerization of phosphates, silicates, and melts were evaluated and indicated a systematic variation in composition. The melt fraction was predicted as a function of temperature and composition. The melting tendency was modeled for three systems, i.e., a P-dominated, a Si-dominated, and a mixed Si-P system. Four ratios between K2O, CaO, MgO, SiO2, and P2O5 were found to have a large effect on the melting tendency of the ash mixtures: the ratio between network formers (SiO2, P2O5), K2O to total network modifiers, CaO to CaO + MgO, and the ratio of network formers to total ash oxides. This modeling approach showed qualitative agreement with ash-related issues seen in previous lab-scale experiments in bubbling fluidized bed and fixed bed combustion. Practical implications of the results are discussed from the perspective of fuel design with the aim of preventing ash-related problems. This study presents a novel method of applying thermodynamic equilibrium calculations for a broad range of compositions and shows potential for predicting ash-related issues related to the melting of coarse ash fractions.

Peer reviewed papers | 2022

Trickle-Bed Bioreactors for Acetogenic H2/CO2 Conversion

Steger F, Ergal I, Daubek A, Loibl N, Rachbauer L, Fuchs W, Rittmann SKMR, Bochmann G. Trickle-Bed Bioreactors for Acetogenic H2/CO2 Conversion. Frontiers in Energy Research. 8 Apirl 2022.10;842284

External Link Details

Acetic acid is an essential industrial building block and can be produced by acetogenic bacteria from molecular hydrogen (H2) and carbon dioxide (CO2). When gasses are supplied as substrates, bioreactor design plays an important role for their availability. Trickle-bed bioreactors (TBs) have an enhanced gas-to-liquid mass transfer and cells remain in the system by forming a biofilm on the carriers. So far, TBs have been investigated extensively for bio-methanation processes, whereas studies for their use in acetic acid production are rare. In this study, we evaluated the reproducibility of two parallel TBs for acetic acid production from H2:CO2 (= 70:30) by a mixed culture with a gas flow rate of 3.8 mL min−1 and a medium flow rate of 10 mL min−1. Additionally, the effect of glucose addition during the starting phase on the resulting products and microbial composition was investigated by setting up a third TB2. Partial medium exchanges to decrease the internal acetic acid concentration (AAC) combined with recycling of withdrawn cells had a positive impact on acetic acid production rates with maxima of around 1 g L−1 d−1 even at high AACs of 19–25 g L−1. Initial glucose addition resulted in the accumulation of unwanted butyric acid up to concentrations of 2.60 ± 0.64 g L−1. The maximum AAC of 40.84 g L−1 was obtained without initial glucose addition. The main families identified in the acetogenic TBs were Peptococcaceae, Ruminococcaceae, Planococcaceae, Enterobacteriaceae, Clostridiaceae, Lachnospiraceae, Dysgonomonadaceae and Tannerellaceae. We conclude that a TB is a viable solution for conversion of H2/CO2 to acetate using an anaerobic enrichment culture.

Peer reviewed papers | 2022

Unknown input observer design for linear time-invariant multivariable systems based on a new observer normal form

Niederwieser H, Tranninger M, Seeber R, Reichhartinger M. Unknown input observer design for linear time-invariant multivariable systems based on a new observer normal form. International Journal of Systems Science. 2022 Apr 6. https://doi.org/10.1080/00207721.2022.2046201

External Link Details

In various applications in the field of control engineering, the estimation of the state variables of dynamic systems in the presence of unknown inputs plays an important role. Existing methods require the so-called observer matching condition to be satisfied, rely on the boundedness e variables or exhibit an increased observer order of at least twice the plant order. In this article, a novel observer normal form for strongly observable linear time-invariant multivariable systems is proposed. In contrast to classical normal forms, the proposed approach also takes the unknown inputs into account. The proposed observer normal form allows for the straightforward construction of a higher-order sliding mode observer, which ensures global convergence of the estimation error within finite time even in the presence of unknown bounded inputs. Its application is not restricted to systems which satisfy the aforementioned limitations of already existing unknown input observers. The proposed approach can be exploited for the reconstruction of unknown inputs with bounded derivative and robust state-feedback control, which is shown by means of a tutorial example. Numerical simulations confirm the effectiveness of the presented work.

Peer reviewed papers | 2022

Unknown Input Observer Design for Linear Time-Invariant Systems - A Unifying Framework

Tranninger M, Niederwieser H, Seeber R, Horn M. Unknown Input Observer Design for Linear Time-Invariant Systems - A Unifying Framework. International Journal of Robust and Nonlinear Control. 2022 Nov 18. https://doi.org/10.1002/rnc.6399

External Link Details

This article presents a new observer design approach for linear time invariant multivariable systems subject to unknown inputs. The design is based on a transformation to the so-called special coordinate basis (SCB). This form reveals important system properties like invertability or the finite and infinite zero structure. Depending on the system's strong observability properties, the SCB allows for a straightforward unknown input observer design utilizing linear or nonlinear observers design techniques. The chosen observer design technique does not only depend on the system properties, but also on the desired convergence behavior of the observer. Hence, the proposed design procedure can be seen as a unifying framework for unknown input observer design.

Conference presentations and posters | 2022

Vereinfachung von Absorptionskälteanlagen-Modellen

Wernhart MW, Rieberer R, Staudt S, Unterberger V, Gölles M. Vereinfachung von Absorptionskälteanlagen-Modellen. Deutsche Kälte- und Klimatagung 2022: DKV-Tagung 2022. 18. November 2022. Magdeburg, Germany.

Details
Other Publications | 2023

Act4Value - Actors for innovative and regional bio residue valorization

Sedlmayer I, Wopienka E. Act4Value - Actors for innovative and regional bio residue valorization. BEST Center Day. 28 June 2023

Download PDF Details

A drastic reduction in the consumption of fossil resources and efficient use are key factors in limiting the further progression of climate change. Cascading use and recycling of residues in the sense of bioeconomy and circular economy are essential. Thermochemical or microbiological conversion can produce various intermediates and endproducts (e.g. biochar, basic chemicals, bioenergy) from biogenic residues. Implemented decentrally, such concepts can reduce transportation efforts, increase the degree of self-sufficiency with raw materials, increase regional added value creation and close (preferably regional) material and energy cycles.

Other Publications | 2023

Advanced Control ot the Generated Steam in a Municipal Waste Incineration Plant

Niederwieser H, Jäger F, Kirnbauer F, Gölles M. Advanced Control ot the Generated Steam in a Municipal Waste Incineration Plant. BEST Center Day. 28 June 2023

Download PDF Details

In modern waste management, the energetic utilization of waste is an important key technology. On the one hand, it allows the waste to be disposed of in an environmentally friendly manner and, on the other hand, makes it possible to reduce the use of other controversial energy sources, such as nuclear fission or fossil fuels. However, the efficient and clean incineration of waste is a challenging task due to the strong inhomogeneity of the waste.

Other Publications | 2023

Alps4GreenC: Implementation pathways for sustainable Green Carbon production in the Alpine Region

Carlon E, Moser K, Seldmayer I, Klauser F. Alps4GreenC: Implementation pathways fpr sustainable Green Carbon production in the Alpine Region. BEST Center Day. 28 June 2023

Download PDF Details

The Alpine Region is characterized by a high density of biomass processing and conversion plants. Alps4GreenC sets the scene for transnational utilization of biomass residues in biochar-based value chains. The project aims at:

  • Researching opportunities for conversion of biomass residues with focus on biochar production.
  • Increasing awareness of citizens, plant owners, policy makers and all involved stakeholders.
  • Establishing connection and coordination among Austria, Italy and Slovenia.
Peer reviewed papers | 2023

Anaerobic acidification of pressed sugar beet pulp for mcl-polyhydroxyalkanoates fermentation

Kacanski M, Knoll L, Nussbaumer M, Neuriter M, Drosg B. Anaerobic acidification of pressed sugar beet pulp for mcl-polyhydroxyalkanoates fermentation. Process Biocemistry.2023:131;235-243,

External Link Details

Anaerobic acidification of pressed sugar beet pulp (PSBP) is a promising strategy for the transition towards a circular economy. In this work, volatile fatty acids were produced by anaerobic acidification of PSBP and subsequently converted to mcl-polyhydroxyalkanoates. The results point to mesophilic acidification as superior to thermophilic one. At the same time, the pH regulated at the value of 6.0 showed a decisive advantage over both the pH of 7.0 and the lack of pH regulation. Furthermore, the conditions with a hydraulic retention time (HRT) of 10 days significantly outperformed those with an HRT of 6 days. The best-performing process (mesophilic, pH controlled at 6, HRT of 10 days) was successfully scaled up to a 250 L reactor, reaching a volatile fatty acid (VFA) concentration of up to 27.8 g L-1. Finally, the produced VFA were investigated as feedstock for mcl-PHA producers, Pseudomonas citronellolis and Pseudomonas putida. Both strains grew and produced PHA successfully, with P. citronellolis reaching a biomass of 15.6 g L-1 with 38% of mcl-PHA, while P. putida grew to 15.2 g L-1 with a polymer content of 31%. This study proves that acidified PSBP is a valuable feedstock for mcl-PHA production and an important approach to developing biorefineries.

Peer reviewed papers | 2023

Automatic thermal model identification and distributed optimisation for load shifting in city quarters

Moser A, Kaisermayer V, Muschick D, Zemann C, Gölles M, Hofer A, Brandl D, Heimrath R, Mach T, Ribas Tugores C, Ramschak T. Automatic thermal model identification and distributed optimisation for load shifting in city quarters, International Journal of Sustainable Energy, 2023;42:1, 1063-1078, DOI: 10.1080/14786451.2023.2246079

External Link Details

Buildings with floor heating or thermally activated building structures offer significant potential for shifting the thermal load and thus reduce peak demand for heating or cooling. This potential can be realised with the help of model predictive control (MPC) methods, provided that sufficiently descriptive mathematical models of the thermal characteristics of the individual thermal zones exist. Creating these by hand is infeasible for larger numbers of zones; instead, they must be identified automatically based on measurement data. In this paper an approach is presented that allows automatically identifying thermal models usable in MPC. The results show that the identified zone models are sufficiently accurate for the use in an MPC, with a mean average error below 1.5K for the prediction of the zone temperatures. The identified zone models are then used in a distributed optimisation scheme that coordinates the individual zones and buildings of a city quarter to best support an energy hub by flattening the overall load profile. In a preliminary simulation study carried out for buildings with floor heating, the operating costs for heating in a winter month were reduced by approximately 9%. Therefore, it can be concluded that the proposed approach has a clear economic benefit.

Filter

Kontaktieren Sie uns

Sie erreichen unser Office unter der Adresse office@best-research.eu

Nutzen Sie auch die Möglichkeit, direkt von dieser Webseite eine Nachricht an unsere Mitarbeiter*innen zu schicken. Schnell und unkompliziert.

Zur Team-Seite